- 您現在的位置：買賣IC網 > PDF目錄224187 > MAX1493CCJ+ (MAXIM INTEGRATED PRODUCTS INC) 3.5- and 4.5-Digit, Single-Chip ADCs with LCD Drivers PDF資料下載
參數資料
| 型號： | MAX1493CCJ+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 3.5- and 4.5-Digit, Single-Chip ADCs with LCD Drivers |
| 中文描述： | 1-CH DELTA-SIGMA ADC, PQFP32 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, MO-136BC, TQFP-32 |
| 文件頁數： | 2/25頁 |
| 文件大?。?/td> | 484K |
| 代理商： | MAX1493CCJ+ |
MAX1491/MAX1493/MAX1495
Internal Clock
The MAX1491/MAX1493/MAX1495 contain an internal
oscillator. Using the internal oscillator saves board
space by removing the need for an external clock
source. The oscillator is optimized to give 50Hz and
60Hz power supply and common-mode rejection.
Charge Pump
The MAX1491/MAX1493/MAX1495 contain an internal
charge pump to provide the negative supply voltage for
the internal analog input/reference buffers. The bipolar
input range of the analog input/reference buffers allows
the devices to accept negative inputs with high source
impedances. For the charge pump to operate correctly,
connect a 0.1F capacitor from VNEG to GND.
LCD Driver
The MAX1491/MAX1493/MAX1495 contain the neces-
sary backplane and segment driver outputs to drive
3.5-digit (MAX1491) and 4.5-digit (MAX1493/MAX1495)
LCDs. The LCD update rate is 2.5Hz. Figures 4–7 show
the connection schemes for a standard LCD. The
MAX1491/MAX1493/MAX1495 automatically display the
results of the ADC.
Triplexing
An internal resistor string of three equal-value resistors
(52k
, 1% matching) is used to generate the display
drive voltages. One end of the string is connected to
DVDD and the other end is connected to GND. Note that
VLCD (VLCD = DVDD - GND) should be three times the
threshold voltage for the liquid-crystal material used.
The connection diagram for a typical 7-segment display
font with two annunciators is illustrated in Figure 3 and
Figure 8. The MAX1491/MAX1493/MAX1495 numeric
display drivers (4.5 digits, 3.5 digits) use this configura-
tion to drive a triplexed LCD with three backplanes and
13 segment driver lines (10 for 3.5 digits). Figures 4 and
5 show the assignment of the 4.5-digit display segments
and Figures 6 and 7 show the assignment of the 3.5-
digit display segments.
The voltage waveforms of the backplane lines and y
segment line (Figure 3) have been chosen as an exam-
ple. This line intersects with BP1 to form the a segment,
with BP2 to form the g segment, and with BP3 to form
the d segment. Eight different ON/OFF combinations of
the a, g, and d segments and their corresponding
waveforms of the y segment line are illustrated in
Figures 9 and 10. The schematic diagram in Figure 8
shows that each intersection acts as a capacitance
from segment line to common line. Figure 11 illustrates
the voltage across the g segment.
The RMS voltage across the segment determines the
degree of polarization for the liquid-crystal material and
thus the contrast of the segment. The RMS OFF voltage
is always VLCD / 3, whereas the RMS ON voltage is
always 1.92VLCD / 3. This is illustrated in Figure 11. The
ratio of RMS ON to OFF voltage is fixed at 1.92 for a
triplexed LCD.
Figure 12 illustrates contrast vs. applied RMS voltage
with a VLCD of 3.1V. The RMS ON voltage is 2.1V and
the RMS OFF voltage is 1.1V. The OFF segment has a
contrast of less than 5%, while the ON segments have
greater than 85% contrast.
3.5- and 4.5-Digit, Single-Chip
ADCs with LCD Drivers
10
______________________________________________________________________________________
Table 1. List of LCD Manufacturers
MANUFACTURER
WEBSITE
PART NUMBER
DESCRIPTION
04-0924-00
3.5 digit, 5V
04-0924-01
3.5 digit, 3V
04-0925-00
4.5 digit, 5V
DCI, Inc.
www.dciincorporated.com
04-0925-01
4.5 digit, 3V
The following site has links to other custom LCD manufacturers: www.earthlcd.com/mfr.htm
a
X
Y
Z
g
d
e
f
c
b
DP
ANNUNCIATOR
a
g
d
e
f
c
b
DP
ANNUNCIATOR
BP1
BP2
BP3
Figure 3. Connection Diagrams for Typical Seven-Segment
Displays
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1510ETB+ | Low-Voltage DDR Linear Regulator |
| MAX151BEWG+T | 300kHz, 10-Bit ADC with Reference and Track/Hold |
| MAX151BCWG+T | 300kHz, 10-Bit ADC with Reference and Track/Hold |
| MAX151BCNG+ | 300kHz, 10-Bit ADC with Reference and Track/Hold |
| MAX151BCWG+ | 300kHz, 10-Bit ADC with Reference and Track/Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1493CCJ+ | 功能描述:模數轉換器 - ADC 4.5 Digit ADC w/LCD Drivers RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1493CCJ+T | 功能描述:模數轉換器 - ADC 4.5 Digit ADC w/LCD Drivers RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1493CCJ-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1493EVKIT+ | 功能描述:數據轉換 IC 開發工具 MAX1493 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1494CCJ | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。