- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX14820ETG+ (Maxim Integrated Products)IC IO-LINK TXRX 24TQFN PDF資料下載
參數資料
| 型號： | MAX14820ETG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC IO-LINK TXRX 24TQFN |
| 標準包裝： | 75 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
MAX14820
IO-Link Device Transceiver
18
Maxim Integrated
Wake-Up Detection
The device detects an IO-Link wake-up condition on the
C/Q line in push-pull, high-side (PNP), or low-side (NPN)
operation modes. A wake-up condition is detected when
the C/Q output is shorted for 80Fs (typ). WU pulses low
for 190Fs (typ) when the device detects a wake-up pulse
on C/Q (Figure 5).
Set the WuIntEn bit in the Mode register to set the WuInt
bit in the Status register and generate an interrupt on
IRQ when a wake-up pulse is detected. WuInt is set
and IRQ asserts immediately after C/Q is released when
WuIntEn = 1.
Thermal Protection and Considerations
The internal LDOs and drivers can generate more power
than the package for the devices can safely dissipate.
Ensure that the driver LDO loading is less than the pack-
age can dissipate. Total power dissipation for the device
is calculated using the following equation:
PTOTAL = PC/Q + PDO + P5 + PLDO33 + PQ +
PCLCQ + PCLDI
where PC/Q is the power generated in the C/Q driver,
PDO is the power dissipated by the DO driver, P5 and
PLDO33 are the power generated by the LDOs, PQ is the
quiescent power generated by the devices, and PCLCQ
and PCLDI are the power generated in the C/Q and DI
current sinks.
Ensure that the total power dissipation is less than the
limits listed in the Absolute Maximum Ratings section.
Use the following to calculate the power dissipation (in
mW) due to the C/Q driver:
PC/Q = [IC/Q(max)] × [0.5 + 7 × IC/Q(max)]
Calculate the internal power dissipation of the DO driver
using the following equation:
PDO = [IDO(max)] × [0.5 + 7 × IDO(max)]
Calculate the power dissipation in the 5V LDO, V5, using
the following equation:
P5 = (VLDOIN - V5) × I5
where I5 includes the ILDO33 current sourced from
LDO33.
Calculate the power dissipated in the 3.3V LDO, LDO33,
using the following equation:
PLDO33 = 1.7V × ILDO33
Calculate the quiescent power dissipation in the device
using the following equation:
PQ = ICC(max) × VCC(max)
If the current sinks are enabled, calculate their associ-
ated power dissipation as:
PCLCQ = ILLM_C/Q(max) × VC/Q(max)
PCLDI = ILLM_DI(max) × VDI(max)
Overtemperature Warning
Bits in the Status and Mode registers are set when the
temperature of the device exceeds +115NC (typ). The
OTempInt bit in the Status register is set and IRQ asserts
when the OTemp bit in the Mode register is set. Read the
Status register to clear the OTempInt bit and IRQ.
The OTemp bit is cleared when the die temperature falls
to +95NC.
The device continues to operate normally unless the
die temperature reaches the +150NC thermal shutdown
threshold, when the device enters thermal shutdown.
Thermal Shutdown
All regulators and the C/Q and DO output drivers are
automatically switched off when the internal die tempera-
ture exceeds the +150NC (typ) thermal shutdown thresh-
old. SPI communication is not available during a thermal
shutdown event.
Regulators are automatically switched on when the inter-
nal die temperature falls below the thermal shutdown
threshold plus hysteresis. The internal registers return to
their default state when the V5 regulator is switched on.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX14821ETG+ | IC IO-LINK 24-TQFN |
| MAX14824GTG+ | IC IO-LINK MASTER TXRX 24TQFN |
| MAX1482CSD-T | IC TXRX RS485/422 250KBPS 14SOIC |
| MAX14830ETM+ | SEMICONDUCTOR OTHER |
| MAX14841EASA+T | IC TXRX RS485 40MBPS 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14820ETG+ | 功能描述:輸入/輸出控制器接口集成電路 IO-Link Device Transceiver RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX14820ETG+T | 功能描述:輸入/輸出控制器接口集成電路 IO-Link Device Transceiver RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX14820EVKIT# | 功能描述:界面開發工具 MAX14820/21 EVAL KIT RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX14821ETG+ | 功能描述:輸入/輸出控制器接口集成電路 NEW RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX14821ETG+T | 功能描述:輸入/輸出控制器接口集成電路 NEW RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。