- 您現在的位置：買賣IC網 > PDF目錄383320 > MAX1478AAE (MAXIM INTEGRATED PRODUCTS INC) 1% Accurate, Digitally Trimmed,Rail-to-Rail Sensor Signal Conditioner PDF資料下載
參數資料
| 型號： | MAX1478AAE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | 1% Accurate, Digitally Trimmed,Rail-to-Rail Sensor Signal Conditioner |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | 5.30 MM, 0.65 MM PITCH, SSOP-16 |
| 文件頁數： | 14/20頁 |
| 文件大?。?/td> | 210K |
| 代理商： | MAX1478AAE |
M
coarse offset TC adjustment is required, use the follow-
ing equation:
where OTC is the sensor offset TC error as a ppm/°C of
OUTFSO (Table 6),
T is the operating temperature
range in °C, and OFFTC COEF is the numerical decimal
value to be loaded into the DAC. For positive values,
set the OFFTC sign bit high; for negative values, set the
OFFTC sign bit low. If the absolute value of the OFFTC
COEF is larger than 4096, the sensor has a very large
offset TC error that the MAX1478 is unable to completely
correct.
FSO Calibration
Perform FSO calibration at room temperature with a full-
scale sensor excitation.
1) Set FSOTC COEF to 1000.
2) At T1, adjust FSO DAC until V
BDRIVE
is about 2.5V.
3) Adjust Offset DAC (and OFFSET sign bit, if needed)
until the T1 offset voltage is 0.5V (see
OFFSET
Calibration
section).
4) Measure the full-span output (measuredV
FSO
).
5) Calculate the ideal bridge voltage, V
BIDEAL
(T1),
using the following equation:
( )
=
Note:
If V
BIDEAL
(T1) is outside the allowable bridge
voltage swing of (V
SS
+ 1.3V) to (V
DD
- 1.3V), readjust
the PGA gain setting. If V
BIDEAL
(T1) is too low,
decrease the PGA gain setting by one step and return
to Step 2. If V
BIDEAL
(T1) is too high, increase the PGA
gain setting by one step and return to Step 2.
6) Set V
BIDEAL
(T1) by adjusting the FSO DAC.
7) Readjust Offset DAC until the offset voltage is 0.5V
(see
OFFSET Calibration
section).
Three-Step FSOTC Compensation
Step 1
Use the following procedure to determine FSOTC
COEF; four variables, A–D, will be used:
1) Name the existing FSO DAC coefficient A.
2) Change FSOTC DAC to 3000.
3) Adjust FSO DAC until V
BDRIVE
(T1) is equal to
V
BIDEAL
(T1).
4) Name the existing FSO DAC coefficient B.
5) Readjust the offset voltage (by adjusting the Offset
DAC), if required, to 0.5V.
At this point, it is important that no other changes be
made to the Offset or Offset TC DACs until the Offset
TC Compensation step has been completed.
Step 2
To complete linear FSOTC compensation, take data
measurements at a second temperature, T2 (T2 > T1).
Perform the following steps:
1) Measure the full-span output (measuredV
FSO
(T2)).
2) Calculate V
BIDEAL
(T2) using the following equation:
(
3) Set V
BIDEAL
(T2) by adjusting the FSO DAC.
4) Name the current FSO DAC coefficient D.
5) Change FSOTC DAC to 1000.
6) Adjust FSO DAC until V
BDRIVE
is equal to
V
BIDEAL
(T2).
7) Name the FSO DAC coefficient C.
Step 3
Insert the data previously obtained from Steps 1 and 2
into the following equation to calculate FSOTC COEF:
1) Load this FSOTC COEF value into the FSOTC DAC.
2) Adjust the FSO DAC until V
BDRIVE
(T2) is equal to
V
BIDEAL
(T2).
This completes both FSO calibration and FSO TC com-
pensation.
FSOTC COEF
1000 B-D
(
3000 C- A
)
+
B-D
C- A
=
)
+
)
)
V
T2
V
1
desiredV
- measuredV
T2
measuredV
T2
BIDEAL
BDRIVE
FSO
FSO
)
FSO
)
=
+
(
)
(
V
1
V
1
desiredV
- measuredV
T
measuredV
T
BIDEAL
BDRIVE
FSO
FSO
FSO
1
1
+
( )
( )
OFFTC COEF
4096 V
T
V
T 2.3
( )
4096 OTC FSO T
(
TCS V
4096 -1000ppm/ C 4V
(
2.3 T
-2100ppm/ C 2.5V 2.3
1357
OUT
BDRIVE
BDRIVE
=
( )
)
=
)
=
1% Accurate, Digitally Trimmed,
Rail-to-Rail Sensor Signal Conditioner
14
______________________________________________________________________________________
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1479EVKIT-315 | Evaluation Kit |
| MAX1479EVKIT-433 | Evaluation Kit |
| MAX147ACAP | +2.7Low-Power, 8-Channel, Serial 12-Bit ADCs |
| MAX147AEAP | +2.7Low-Power, 8-Channel, Serial 12-Bit ADCs |
| MAX146ACAP | .1 UF/400VDC METAL POLY CAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1478AAE-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1478CAE | 功能描述:板上安裝溫度傳感器 Rail-to-Rail Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1478CAE-T | 功能描述:板上安裝溫度傳感器 Rail-to-Rail Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1479ATE | 功能描述:射頻發射器 RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| MAX1479ATE+ | 功能描述:射頻發射器 300MHz - 450MHz ASK/FSK Transmitter RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。