- 您現在的位置：買賣IC網 > PDF目錄383320 > MAX1472EVKIT-433 (Maxim Integrated Products, Inc.) Evaluation Kit PDF資料下載
參數資料
| 型號： | MAX1472EVKIT-433 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Evaluation Kit |
| 中文描述： | 評估板 |
| 文件頁數： | 3/5頁 |
| 文件大?。?/td> | 463K |
| 代理商： | MAX1472EVKIT-433 |
5) Calculate the efficiency. This is done using the fol-
lowing equation:
Efficiency = 10 ^ (Pout / 10) / (V x I)
where I is in mA.
For example, the efficiency is 46.6% for an output of
+11dBm, and a current of 9mA (at 3.0V).
Layout Issues
A properly designed PC board is an essential part of
any RF/microwave circuit. On high-frequency inputs
and outputs, use controlled-impedance lines and keep
them as short as possible to minimize losses and radia-
tion. At high frequencies, trace lengths that are on the
order of
λ
/10 or longer can act as antennas.
Keeping the traces short also reduces parasitic induc-
tance. Generally, 1in of a PC board trace adds about
20nH of parasitic inductance. The parasitic inductance
can have a dramatic effect on the effective inductance.
For example, a 0.5in trace connecting a 100nH induc-
tor adds an extra 10nH of inductance or 10%.
To reduce the parasitic inductance, use wider traces
and a solid ground or power plane below the signal
traces. Also, use low-inductance connections to ground
on all GND pins, and place decoupling capacitors
close to all VDD connections.
The EV kit PC board can serve as a reference design
for laying out a board using the MAX1472.
Detailed Description
Enable Control
The MAX1472 can be controlled externally using the
ENABLE connector. The IC draws approximately 1nA
(at room temperature) in shutdown mode. Jumper JU1
is used to control this mode. The shunt can be placed
between pins 1 and 2 for continuous operation.
Remove the JU1 shunt for external control. See Table 1
for jumper function descriptions.
Table 1. Jumper Functions
Data Input
The MAX1472 EV kit transmits ASK data with data rates
up to 100kbps. JU2 controls whether the MAX1472
transmits CW (jumper pins 1 and 2 connected), an
external data stream (no jumper), or train pulses gener-
ated by the ICM7555 timer (jumper pins 2 and 3 con-
nected). JU4 controls whether the ICM7555 data is
being generated continuously or at the push of SW1.
REF_IN External Frequency Input
For applications where the correct frequency crystal is
not available, it is possible to directly inject an external
frequency through the REF_IN SMA (not provided).
Connect the SMA to a low-phase-noise generator. The
addition of C18 and C19 is necessary (use 0.01
μ
F
capacitors).
Battery Operation
The MAX1472 EV kit can be powered by an external
power supply or by the supplied 3V coin-cell battery.
Set jumper JU3 to connect pins 2 and 3 for battery
operation.
RF Output
The MAX1472 EV kit includes two SMA connectors for RF
output. RFOUT is a standard SMA and is used to connect
the PA output to test equipment. Output is matched to
50
. ANTENNA_OUT is a reverse polarity SMA and is
used to connect to a 1/4 wave whip antenna . Note that
resistor R2 (0
) needs to be added.
I/O Connections
Table 2 lists all I/O connections.
For additional information and a list of application
notes, consult the Maxim website, www/maxim-ic.com.
E
MAX1472 Evaluation Kit
_______________________________________________________________________________________
3
JUMPER
JU1
JU1
JU2
JU2
JU2
JU3
JU3
JU4
JU4
STATE
1-2
NC
1-2
2-3
NC
1-2
2-3
1-2
NC
FUNCTION
Normal operation
External power-down control
RF carrier-transmit mode
Transmit pulse-train mode
External data transmit
External supply operation
Battery operation
Continuous data generation
Data controlled by SW1
Table 2. I/O Connectors
SIGNAL
RFOUT
REF_IN
DESCRIPTION
RF output
External reference frequency input
ANTENNA_OUT
Reverse polarity SMA for 1/4 wave
antenna
VSS
VDD
Ground
3.0V power input
Data input
External power-down control
DATA_IN
ENABLE
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1473EVKIT-315 | Evaluation Kit |
| MAX1473EVKIT-433 | Evaluation Kit |
| MAX1478 | 1% Accurate, Digitally Trimmed,Rail-to-Rail Sensor Signal Conditioner |
| MAX1478AAE | 1% Accurate, Digitally Trimmed,Rail-to-Rail Sensor Signal Conditioner |
| MAX1479EVKIT-315 | Evaluation Kit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1472EVKIT-433# | 功能描述:射頻開發工具 MAX1472 Eval Kit RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| MAX1473ETJ | 制造商:Maxim Integrated Products 功能描述:315MHZ/433MHZ ASK SUPERHETERODYNE RECEIVER WI - Rail/Tube |
| MAX1473ETJ+ | 功能描述:射頻接收器 315MHz/434MHz Superheterodyne Rcvr RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| MAX1473ETJ+T | 功能描述:射頻接收器 315MHz/434MHz Superheterodyne Rcvr RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| MAX1473ETJ-T | 制造商:Maxim Integrated Products 功能描述:315MHZ/433MHZ ASK SUPERHETERODYNE RECEIVER WI - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。