參數資料
型號： MAX1452
廠商： Maxim Integrated Products, Inc.
英文描述： Low-Cost Precision Sensor Signal Conditioner
中文描述： 低成本、高精度傳感器信號調理器
文件頁數： 8/24頁
文件大?。?/td> 283K
代理商： MAX1452
M
ture errors. The piezoresistive sensor is powered by a
current source resulting in a temperature-dependent
bridge voltage due to the sensor's temperature resis-
tance coefficient (TCR). The reference inputs of the off-
set TC DAC and FSOTC DAC are connected to the
bridge voltage. The DAC output voltages will track the
bridge voltage as it varies with temperature, and by
varying the offset TC and FSOTC digital code a portion
of the bridge voltage, which is temperature dependent,
is used to compensate the first order temperature
errors.
The internal feedback resistors (R
ISRC
and R
STC
) for
FSO temperature compensation are optimized to 75k
for silicon piezoresistive sensors. However, since the
required feedback resistor values are sensor depen-
dent, external resistors may also be used. The internal
resistors selection bit in the configuration register
selects between internal and external feedback resis-
tors.
To calculate the required offset TC and FSOTC com-
pensation coefficients, two test-temperatures are need-
ed. After taking at least two measurements at each
temperature, calibration software (in a host computer)
calculates the correction coefficients and writes them to
the internal EEPROM.
With coefficients ranging from 0000hex to FFFFhex and
a +5V reference, each DAC has a resolution of 76μV.
Two of the DACs (offset TC and FSOTC) utilize the sen-
sor bridge voltage as a reference. Since the sensor
bridge voltage is approximately set to +2.5V the FSOTC
and offset TC exhibit a step size of less than 38μV.
For high accuracy applications (errors less than
0.25%), the first-order offset and FSOTC should be
compensated with the offset TC and FSOTC DACs, and
the residual higher order terms with the lookup table.
The offset and FSO compensation DACs provide
unique compensation values for approximately 1.5
°
C of
temperature change as the temperature indexes the
address pointer through the coefficient lookup table.
Changing the offset does not effect the FSO, however
changing the FSO will affect the offset due to nature of
the bridge. The temperature is measured on both the
MAX1452 die and at the bridge sensor. It is recom-
mended to compensate the first-order temperature
errors using the bridge sensor temperature.
Typical Ratiometric
Operating Circuit
Ratiometric output configuration provides an output that
is proportional to the power supply voltage. This output
can then be applied to a ratiometric ADC to produce a
digital value independent of supply voltage.
Ratiometricity is an important consideration for battery-
operated instruments, automotive, and some industrial
applications.
The MAX1452 provides a high-performance ratiometric
output with a minimum number of external components
(
Figure 2
). These external components include the fol-
lowing:
One supply bypass capacitor.
One optional output EMI suppression capacitor.
Two optional resistors, RISRC and RSTC, for special
sensor bridge types.
Low-Cost Precision Sensor
Signal Conditioner
8
_______________________________________________________________________________________
Figure 2. Basic Ratiometric Output Configuration
MAX1452
+5V V
DD
OUT
GND
RSTC
RISRC
0.1
μ
F
0.1
μ
F
INM
TEST V
SS
8
INP
7
9
2
16
1
3
BDR
V
DDF
OUT
5
6
4
FSOTC
ISRC
SENSOR
V
DD
相關PDF資料
PDF描述
MAX1452AAE Low-Cost Precision Sensor Signal Conditioner
MAX1452CAE Low-Cost Precision Sensor Signal Conditioner
MAX1452EAE Low-Cost Precision Sensor Signal Conditioner
MAX1457 0.1%-Accurate Signal Conditioner for Piezoresistive Sensor Compensation
MAX1457ACJ 0.1%-Accurate Signal Conditioner for Piezoresistive Sensor Compensation
相關代理商/技術參數
參數描述
MAX14521EETG+ 功能描述:顯示驅動器和控制器 Quad High-Voltage EL Lamp Driver w/I2C RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
MAX14521EETG+T 功能描述:顯示驅動器和控制器 Quad High-Voltage EL Lamp Driver w/I2C RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
MAX14521EEVKIT+ 功能描述:顯示開發工具 Quad High-Voltage EL Lamp Driver with I C Interface RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V
MAX14522AEWC+T 功能描述:PMIC 解決方案 RS-485 Transceiver w/Low-V Logic Int RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
MAX14522EWC+T 功能描述:PMIC 解決方案 RS-485 Transceiver w/Low-V Logic Int RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*