- 您現在的位置：買賣IC網 > PDF目錄383319 > MAX1415CNE (MAXIM INTEGRATED PRODUCTS INC) 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs PDF資料下載
參數資料
| 型號： | MAX1415CNE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs |
| 中文描述： | 2-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDIP16 |
| 封裝： | 0.300 INCH, PLASTIC, MS-001AA, DIP-16 |
| 文件頁數： | 9/36頁 |
| 文件大?。?/td> | 669K |
| 代理商： | MAX1415CNE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
M
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADCs
_______________________________________________________________________________________
9
Note 1:
These errors are in the order of the conversion noise shown in Tables 1 and 3. This applies after calibration at the given
temperature.
Recalibration at any temperature removes these drift errors.
Positive full-scale error includes zero-scale errors (unipolar offset error or bipolar zero error) and applies to both unipolar
and bipolar input ranges.
Full-scale drift includes zero-scale drift (unipolar offset drift or bipolar zero drift) and applies to both unipolar and bipolar
input ranges.
Gain error does not include zero-scale errors. It is calculated as (full-scale error – unipolar offset error) for unipolar ranges,
and (full-scale error – bipolar zero error) for bipolar ranges.
Gain-error drift does not include unipolar offset drift or bipolar zero drift. Effectively, it is the drift of the part if only zero-
scale calibrations are performed.
The analog input voltage range on AIN+ is given here with respect to the voltage on AIN- on the MAX1415/MAX1416.
This common-mode voltage range is allowed, provided that the input voltage on the analog inputs does not go more posi-
tive than (V
DD
+ 30mV) or more negative than (GND - 30mV). Parts are functional with voltages down to (GND - 200mV),
but with increased leakage at high temperature.
Note 9:
The REF differential voltage, V
REF
, is the voltage on REF+ referenced to REF- (V
REF
= V
REF+
- V
REF-)
.
Note 10:
Guaranteed by design.
Note 11:
These calibration and span limits apply, provided that the absolute voltage on the analog inputs does not exceed (V
DD
+
30mV) or go more negative than (GND - 30mV). The offset-calibration limit applies to both the unipolar zero point and the
bipolar zero point.
Note 12:
When using a crystal or ceramic resonator across the CLKIN and CLKOUT as the clock source for the device, the supply
current and power dissipation varies depending on the crystal or resonator type. Supply current is measured with the digi-
tal inputs connected to 0 or V
DD
, CLKIN connected to an external clock source, and CLKDIS = 1.
Note 13:
If the external master clock continues to run in power-down mode, the power-down current typically increases to 67μA at
3V. When using a crystal or ceramic resonator across the CLKIN and CLKOUT as the clock source for the device, the
clock generator continues to run in power-down mode and the power dissipation depends on the crystal or resonator type
(see the
Power-Down Modes
section).
Note 14:
Measured at DC and applied in the selected passband. PSRR at 50Hz exceeds 120dB with filter notches of 25Hz or 50Hz.
PSRR at 60Hz exceeds 120dB with filter notches of 20Hz or 60Hz.
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
PSRR depends on both gain and V
DD
.
Note 15:
Provide f
CLKIN
whenever the MAX1415/MAX1416 are not in power-down mode. If no clock is present, the device can draw
higher-than-specified current and can possibly become uncalibrated.
Note 16:
All input signals are specified with t
r
= t
f
= 5ns (10% to 90% of V
DD
) and timed from a voltage level of 1.6V.
GAIN
PSRR (V
DD
= 5V)
PSRR (V
DD
= 3V)
(dB)
1
2
4
90
78
84
91
86
78
85
93
8 to 128
TIMING CHARACTERISTICS—MAX1416 (continued)
(Note 16) (Figures 8, 9)
PARAMETER
SYMBOL
DIN to SCLK Setup Time
DIN to SCLK Hold Time
CONDITIONS
MIN
30
20
TYP
MAX
UNITS
ns
ns
t
9
t
10
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1415CUE | 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs |
| MAX1415CWE | 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs |
| MAX1415ENE | 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs |
| MAX1415EUE | 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs |
| MAX1415EWE | 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1415ENE | 制造商:Maxim Integrated Products 功能描述:16-BIT, LOW-POWER, 2-CHANNEL, SIGMA-DELTA ADC - Rail/Tube |
| MAX1415EPE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1415EPE+ | 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1415EUE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1415EUE+ | 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。