參數資料
型號： MAX1415
廠商： Maxim Integrated Products, Inc.
元件分類： ADC
英文描述： 16-Bit. Low-Power. 2-Channel. Sigma-Delta ADCs
中文描述： 16位、低功耗、2通道、Σ-Δ ADC
文件頁數： 26/36頁
文件大?。?/td> 669K
代理商： MAX1415
M
Clock Register
The byte-wide clock register is bidirectional, so it can
be written and read. The byte written to the setup regis-
ter sets the clock, filter first notch frequency, and the
output data rate (see Table 12).
MXID:
(Default = 1) Maxim-Identifier Bit. This is a read-
only bit. Values written to this bit are ignored.
ZERO:
(Default = 0) Zero Bit. This is a read-only bit.
Values written to this bit are ignored.
INTCLK:
(Default = 0) Internal Oscillator Bit. Set INTCLK
= 1 to enable the internal oscillator. Set INTCLK = 0 to
disable the internal oscillator.
CLKDIS:
(Default = 0) Clock-Disable Bit. Set CLKDIS = 1
to disable the internally or externally generated clock from
appearing on CLKOUT. When using a crystal or res-
onator across CLKIN and CLKOUT, the clock is stopped
and no conversions take place when CLKDIS = 1.
CLKOUT is held low during clock disable to save power.
Set CLKDIS = 0 to allow other devices to use the output
signal on CLKOUT as a clock source and/or to enable the
external oscillator. The CLKOUT pin on the MAX1415/
MAX1416 can drive one CMOS load.
CLKDIV:
(Default = 0) Clock-Divider Control Bit. The
MAX1415/MAX1416 each have an internal clock divider.
Set this bit to 1 to divide the input clock by two. When this
bit is set to 0, the MAX1415/MAX1416 operate at the
internal or external oscillator frequency. CLKDIV has no
effect on the internal oscillator.
CLK:
(Default = 1) Clock Bit. When using the internal
oscillator (INTCLK = 1), set CLK = 1 for a frequency of
2.4576MHz, and set CLK = 0 for a frequency of 1MHz.
When using an external clock/oscillator, set CLK = 1 for
f
CLKIN
= 2.4576MHz with CLKDIV = 0, or f
CLKIN
=
4.9152MHz with CLKDIV = 1.
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADCs
26
______________________________________________________________________________________
Table 10. Operating-Mode Selection
MD1
0
MD0
0
OPERATING MODE
Normal Mode. Use this mode to perform normal conversions on the selected analog input channel.
Self-Calibration Mode. This mode performs self-calibration on the selected channel determined from CH0 and
CH1 selection bits in the communications register (Table 6). Upon completion of self-calibration, the device
returns to normal mode with MD1, MD0 returning to 0, 0. The
DRDY
output bit goes high when self-calibration is
requested and returns low when the calibration is complete and a new data word is in the data register. Self-
calibration performs an internal zero-scale and full-scale calibration. The analog inputs of the device are shorted
together internally during zero-scale calibration and connected to an internally generated (V
REF
/GAIN) voltage
during full-scale calibration. The offset and gain registers for the selected channel are automatically updated
with the calibration data.
Zero-Scale System-Calibration Mode. This mode performs zero-scale calibration on the selected channel
determined from CH1 and CH0 selection bits in the communications register (Table 6). The
DRDY
output bit
goes high when calibration is requested and returns low when the calibration is complete and a new data word
is in the data register. Performing zero-scale calibration compensates for any DC offset voltage present in the
ADC and system. Ensure that the analog input voltage is stable within 0.5 LSB for the duration of the calibration
sequence. The offset register for the selected channel is updated with the zero-scale system-calibration data.
Upon completion of calibration, the device returns to normal mode with MD1, MD0 returning to 0, 0.
Full-Scale System-Calibration Mode. This mode performs full-scale system-calibration on the selected channel
determined from CH1 and CH0 selection bits in the communications register. This calibration assigns a full-
scale output code to the voltage present on the selected channel. Ensure that the analog input voltage is stable
within 0.5 LSB for the duration of the calibration sequence. The
DRDY
output bit goes high during calibration
and returns low when the calibration is complete and a new data word is in the data register. The gain register
for the selected channel is updated with the full-scale system-calibration data. Upon completion of calibration,
the device returns to normal mode with MD1, MD0 returning to 0, 0.
0
1
1
0
1
1
Table 11. PGA Gain Selection
G2
0
0
0
0
1
1
1
1
G1
0
0
1
1
0
0
1
1
G0
0
1
0
1
0
1
0
1
PGA GAIN
1
2
4
8
16
32
64
128
相關PDF資料
PDF描述
MAX1416 16-Bit. Low-Power. 2-Channel. Sigma-Delta ADCs
MAX1415AEUE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1415AEWE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1415CNE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1415CUE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
相關代理商/技術參數
參數描述
MAX1415AENE 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415AEUE 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415AEWE 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415AEWE+ 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415AEWE+T 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*