- 您現在的位置：買賣IC網 > PDF目錄2008 > MAX1394ETB+T (Maxim Integrated Products)IC ADC 8BIT 416KSPS 10-TDFN-EP PDF資料下載
參數資料
| 型號： | MAX1394ETB+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 8BIT 416KSPS 10-TDFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 位數： | 8 |
| 采樣率（每秒）： | 416k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 1.48W |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-TDFN-EP（3x3） |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 2 個單端，單極；2 個單端，雙極；1 個差分，單極；1 個差分，雙極 |
| 產品目錄頁面： | 1396 (CN2011-ZH PDF) |
| 其它名稱： | MAX1394ETB+TDKR |
Signal-to-Noise Ratio (SNR)
SNR is a dynamic figure of merit that indicates the con-
verter’s noise performance. For a waveform perfectly
reconstructed from digital samples, the theoretical
maximum SNR is the ratio of the full-scale analog input
(RMS value) to the RMS quantization error (residual
error). The ideal, theoretical minimum analog-to-digital
noise is caused by quantization error only and results
directly from the ADC’s resolution (N bits):
SNRdB[max] = 6.02dB x N + 1.76dB
In reality, there are other noise sources such as thermal
noise, reference noise, and clock jitter that also
degrade SNR. SNR is computed by taking the ratio of
the RMS signal to the RMS noise. RMS noise includes
all spectral components to the Nyquist frequency
excluding the fundamental, the first five harmonics, and
the DC offset.
Total Harmonic Distortion (THD)
THD is a dynamic figure of merit that indicates how much
harmonic distortion the converter adds to the signal.
THD is the ratio of the RMS sum of the first five harmon-
ics of the fundamental signal to the fundamental itself.
This is expressed as:
where V1 is the fundamental amplitude, and V2 through
V6 are the amplitudes of the 2nd- through 6th-order
harmonics.
Spurious-Free Dynamic Range (SFDR)
SFDR is a dynamic figure of merit that indicates the
lowest usable input signal amplitude. SFDR is the ratio
of the RMS amplitude of the fundamental (maximum
signal component) to the RMS value of the next-largest
spurious component, excluding DC offset. SFDR is
specified in decibels relative to the carrier (dBc).
Intermodulation Distortion (IMD)
IMD is the ratio of the RMS sum of the intermodulation
products to the RMS sum of the two fundamental input
tones. This is expressed as:
The fundamental input tone amplitudes (V1 and V2) are
at -6.5dBFS. 14 intermodulation products (VIM_) are
used in the MAX1391/MAX1394 IMD calculation. The
intermodulation products are the amplitudes of the out-
put spectrum at the following frequencies, where fIN1
and fIN2 are the fundamental input tone frequencies:
2nd-order intermodulation products:
fIN1 + fIN2, fIN2 - fIN1
3rd-order intermodulation products:
2 x fIN1 - fIN2, 2 x fIN2 - fIN1, 2 x fIN1 + fIN2, 2 x fIN2 + fIN1
4th-order intermodulation products:
3 x fIN1 - fIN2, 3 x fIN2 - fIN1, 3 x fIN1 + fIN2, 3 x fIN2 + fIN1
5th-order intermodulation products:
3 x fIN1 - 2 x fIN2, 3 x fIN2 - 2 x fIN1, 3 x fIN1 + 2 x fIN2,
3 x fIN2 + 2 x fIN1
Channel-to-Channel Crosstalk
Channel-to-channel crosstalk indicates how well each
analog input is isolated from the others. The channel-to-
channel crosstalk for the MAX1394 is measured by
applying DC to channel 2 while a sine wave is applied
to channel 1. An FFT is taken for channels 1 and 2, and
the difference (in dB) is reported as the channel-to-
channel crosstalk.
Aperture Delay
The MAX1391/MAX1394 sample data on the falling
edge of its third SCLK cycle (Figure 14). In actuality,
there is a small delay between the falling edge of the
sampling clock and the actual sampling instant.
Aperture delay (tAD) is the time defined between the
IMD
VV
V
VV
IM
IMN
log
.....
=×
++
+
20
1
2
3
22
1
2
THD
VVVVV
V
log
=×
++++
20
2
3
2
4
2
5
2
6
2
1
MAX1391/MAX1394
______________________________________________________________________________________
15
1.5V to 3.6V, 416ksps, 1-Channel True-Differential/
2-Channel Single-Ended, 8-Bit, SAR ADCs
10
Ω
(OPTIONAL)
VDD
POWER SUPPLY
GND
DIGITAL
CIRCUITRY
GND
DGND
DATA
STAR
GROUND
POINT
DVDD
VDD
MAX1391/MAX1394
Figure 13. Power-Supply Grounding Connections
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1395ETB+T | IC ADC 10BIT 357KSPS 10-TDFN |
| MAX1400CAI+ | IC ADC 18BIT LP 28-SSOP |
| MAX1401CAI+ | IC ADC 18BIT LP 28-SSOP |
| MAX1415AEWE+T | IC ADC 16BIT DELTA SIGMA 16-SOIC |
| MAX1421CCM+D | IC ADC 12BIT 40MSPS 48LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1394MTB+T | 功能描述:模數轉換器 - ADC 8-Bit 2Ch 400ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1394MTB-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1395ETB | 制造商:Maxim Integrated Products 功能描述:1.5V-3.6V357KSPS1-CHANNEL TRUE-DI - Rail/Tube |
| MAX1395ETB+ | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 357KSPS 10-BIT SERL 10TDFN EP - Rail/Tube |
| MAX1395ETB+T | 功能描述:模數轉換器 - ADC 10-Bit 2Ch 357ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。