- 您現在的位置：買賣IC網 > PDF目錄10581 > MAX1393ETB+T (Maxim Integrated Products)IC ADC 12BIT 312.5KSPS 10-TDFN PDF資料下載
參數資料
| 型號： | MAX1393ETB+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 18/18頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 312.5KSPS 10-TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 312.5k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 830µW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-TDFN-EP（3x3） |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 2 個單端，單極；2 個單端，雙極；1 個差分，單極；1 個差分，雙極 |
| 產品目錄頁面： | 1396 (CN2011-ZH PDF) |
| 其它名稱： | MAX1393ETB+TDKR |
and the difference between the sampled positive and
negative input voltages is converted. The time required
for the T/H to acquire an input signal is determined by
how quickly its input capacitance is charged. The
required acquisition time lengthens as the input signal’s
source impedance increases. The acquisition time,
tACQ, is the minimum time needed for the signal to be
acquired. It is calculated by the following equation:
tACQ
≥ 9 x (RSOURCE + RIN) x CIN + tPU
where:
RSOURCE is the source impedance of the input signal.
RIN = 500
Ω, which is the equivalent differential analog
input resistance.
CIN = 16pF, which is the equivalent differential analog
input capacitance.
tPU = 400ns.
Note: tACQ is never less than 600ns and any source
impedance below 400
Ω does not significantly affect the
ADC’s AC performance.
Analog Input Bandwidth
The ADC’s input-tracking circuitry has a 4MHz full-
power bandwidth, making it possible to digitize high-
speed transient events and measure periodic signals
with bandwidths exceeding the ADC’s sampling rate by
using undersampling techniques.
Use anti-alias filtering to avoid high-frequency signals
being aliased into the frequency band of interest.
Analog Input Range and Protection
The MAX1393/MAX1396 produce a digital output that
corresponds to the analog input voltage as long as the
analog inputs are within their specified range. When
operating the MAX1393 in unipolar mode (UNI/BIP = 1),
the specified differential analog input range is from 0 to
VREF. When operating in bipolar mode (UNI/BIP = 0),
the differential analog input range is from -VREF/2 to
+VREF/2 with a common-mode range of 0 to VDD. The
MAX1396 has an input range from 0 to VREF.
Internal protection diodes confine the analog input volt-
age within the region of the analog power input rails
(VDD, GND) and allow the analog input voltage to swing
from GND - 0.3V to VDD + 0.3V without damage. Input
voltages beyond GND - 0.3V and VDD + 0.3V forward
bias the internal protection diodes. In this situation, limit
the forward diode current to less than 50mA to avoid
damage to the MAX1393/MAX1396.
Output Data Format
Figures 8, 9, and 10 illustrate the conversion timing for
the MAX1393/MAX1396. Sixteen SCLK cycles are
required to read the conversion result and data on
DOUT transitions on the falling edge of SCLK. The con-
version result contains 4 zeros, followed by 12 data bits
with the data in MSB-first format. For the MAX1393, data
is straight binary for unipolar mode and two’s comple-
ment for bipolar mode. For the MAX1396, data is always
straight binary.
Transfer Function
Figure 5 shows the unipolar transfer function for the
MAX1393/MAX1396. Figure 6 shows the bipolar trans-
fer function for the MAX1393. Code transitions occur
halfway between successive-integer LSB values.
MAX1393/MAX1396
_______________________________________________________________________________________
9
1.5V to 3.6V, 312.5ksps, 1-Channel True-Differential/
2-Channel Single-Ended, 12-Bit, SAR ADCs
+
-
HOLD
TRACK
CIN+
REF
GND
DAC
CIN-
RIN+
RIN-
VDD/2
RSOURCE
COMPARATOR
HOLD
AIN2
AIN1 (AIN+)*
GND (AIN-)*
ANALOG
SIGNAL
SOURCE
MAX1393
MAX1396
*INDICATES THE MAX1393
Figure 4. Equivalent Input Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MS3102E20-6S | CONN RCPT 3POS BOX MNT W/SCKT |
| VE-B51-MX-F3 | CONVERTER MOD DC/DC 12V 75W |
| VE-25P-MX | CONVERTER MOD DC/DC 13.8V 75W |
| SP490EEN-L | IC TXRX RS485 FULL DUPLEX 8NSOIC |
| VE-B50-MX-F2 | CONVERTER MOD DC/DC 5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1393MTB+T | 功能描述:模數轉換器 - ADC 12-Bit 312ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1393MTB-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1394ETB | 制造商:Maxim Integrated Products 功能描述:1.5V TO 3.6V 416KSPS 1-CHANNEL 8-BIT, SAR ADCS - Rail/Tube |
| MAX1394ETB+ | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 416KSPS 8BIT SERL 10TDFN EP - Rail/Tube |
| MAX1394ETB+T | 功能描述:模數轉換器 - ADC 8-Bit 2Ch 400ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。