- 您現在的位置：買賣IC網 > PDF目錄2008 > MAX1361MEUB+T (Maxim Integrated Products)IC SYSTEM MON 10BIT 4CH 10-UMAX PDF資料下載
參數資料
| 型號： | MAX1361MEUB+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SYSTEM MON 10BIT 4CH 10-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 10 |
| 采樣率（每秒）： | 150k |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 2mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個差分，單極；2 個差分，雙極 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
MAX1361/MAX1362
be addressed with a read command to obtain new con-
version results.
External Clock
See the
Configuration/Setup Bytes (Write Cycle) section.
When configured for external clock mode (INT/EXT = 1),
the MAX1361/MAX1362 use SCL as the conversion clock.
In external clock mode, the MAX1361/MAX1362 begin
tracking the analog input on the eighth rising clock edge
of a valid slave address byte. Two SCL clock cycles later,
the analog signal is acquired and the conversion begins.
Unlike internal clock mode, converted data is clocked out
immediately in the format described in the
Reading a
Conversion (Read Cycle) section.
The device continuously converts input channels dictat-
ed by the scan mode until given a not acknowledge
(NACK). There is no need to readdress the device with
a read command to obtain new conversion results.
The conversion must complete in 1ms or droop on the
T/H capacitor degrades conversion results. Use internal
clock mode if the SCL clock period exceeds 60s.
Use external clock mode for conversion rates from
40ksps to 94.4ksps. Use internal clock mode for con-
versions under 40ksps. Internal clock mode consumes
less power. Monitor mode always uses internal clock
mode regardless of conversion rate.
Applications Section
Power-On Reset
The configuration and setup registers default to a sin-
gle-ended, unipolar, single-channel conversion on AIN0
using the internal clock with VDD as the reference and
AIN3/REF configured as an analog input. The memory
contents are unknown at power-up (see the
Software
Description section).
I2C-Compatible 2-Wire Serial Interface
The MAX1361/MAX1362 use an I2C-compatible 2-wire
interface consisting of a serial-data line (SDA) and seri-
al-clock line (SCL). SDA and SCL facilitate bidirectional
communication between the MAX1361/MAX1362 and
the master at rates up to 1.7MHz. The master (typically
a microcontroller) initiates data transfer on the bus and
generates the SCL signal to permit data transfer. The
MAX1361/MAX1362 behave as I2C slave devices that
transfer and receive data.
SDA and SCL must be pulled high for proper I2C opera-
tion. This is typically done with pullup resistors (750
Ω or
greater). Series resistors (RS) are optional (see the
Typical Operating Circuit section). The resistors protect
the input architecture of the MAX1361/MAX1362 from
high voltage spikes on the bus lines and minimize
crosstalk and undershoot of the bus signals.
One bit transfers during each SCL clock cycle. A mini-
mum of nine clock cycles is required to transfer a byte
in or out of the MAX1361/MAX1362 (8 bits and an
ACK/NACK). The data on SDA must remain stable dur-
ing the high period of the SCL clock pulse. Changes in
SDA while SCL is high and stable are considered con-
trol signals (see the
START and STOP Conditions sec-
tion). Both SDA and SCL remain high when the bus is
not busy.
START and STOP Conditions
The master initiates a transmission with a START condi-
tion (S), which is a high-to-low transition on SDA while
SCL is high. The master terminates a transmission with
a STOP condition (P), which is a low-to-high transition
on SDA while SCL is high (Figure 4). A repeated START
condition (Sr) can be used in place of a STOP condition
to leave the bus active and the mode unchanged (see
the
HS I2C Mode section).
Acknowledge and Not-Acknowledge Conditions
Data transfers are framed with an acknowledge bit
(ACK) or a not-acknowledge bit (NACK). Both the mas-
ter and the MAX1361/MAX1362 (slave) generate
acknowledge bits. To generate an acknowledge, the
receiving device must pull SDA low before the rising
edge of the acknowledge-related clock pulse (ninth
pulse) and keep it low during the high period of the
clock pulse (Figure 5).
4-Channel, 10-Bit, System Monitor with Programmable
Trip Window and SMBus Alert Response
12
______________________________________________________________________________________
SCL
SDA
SP
Sr
Figure 4. START and STOP Conditions
SCL
SDA
S
NOT ACKNOWLEDGE
ACKNOWLEDGE
12
8
9
Figure 5. Acknowledge Bits
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1364MEUB+T | IC SYSTEM MON 12BIT 4CH 10-UMAX |
| MAX1394ETB+T | IC ADC 8BIT 416KSPS 10-TDFN-EP |
| MAX1395ETB+T | IC ADC 10BIT 357KSPS 10-TDFN |
| MAX1400CAI+ | IC ADC 18BIT LP 28-SSOP |
| MAX1401CAI+ | IC ADC 18BIT LP 28-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1362EUB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1362EUB+ | 功能描述:模數轉換器 - ADC 10-Bit 4Ch 150ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1362EUB+T | 功能描述:模數轉換器 - ADC 10-Bit 4Ch 150ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1362EUB-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1362LEUB+T | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 150KSPS 10-BIT SERL 10PIN UMAX - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。