參數資料
型號： MAX1358BETL+
廠商： Maxim Integrated Products
文件頁數： 60/71頁
文件大?。?/td> 0K
描述： IC DAS 16BIT 40-TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
類型： 數據采集系統（DAS）
分辨率（位）： 16 b
采樣率（每秒）： 21.94k
數據接口： MICROWIRE?，QSPI?，串行，SPI?
電壓電源： 模擬和數字
電源電壓： 1.8 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 40-WFQFN 裸露焊盤
供應商設備封裝： 40-TQFN-EP（6x6）
包裝： 托盤
MAX1358B
16-Bit, Data-Acquisition System with ADC, DACs,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
______________________________________________________________________________________
63
MAX1358B
32KIN
100k
Ω
CMOS CLOCK
(0 TO DVDD)
100k
Ω
Figure 25. Clocking with a CMOS Signal
MAX1358B
UPIO1
GPIOn
AIN1
x2
VREF = 1.25V
BATTVCHECK
< 0.6125V
VBATT1
BACKLIGHT
VDD
NOTE:
GPIOn IS LOW = LED ON,
HIGH-Z = LED OFF
μP
VBATT2
Figure 26. Input Multiplexer
Clocking with a CMOS Signal
A CMOS signal can be used to drive 32KIN if it is divid-
ed down. Figure 25 is an example circuit, which works
well.
Input Multiplexer
The mux inputs can range between AGND and AVDD.
However, when the internal temperature sensor is
enabled, AIN1 and AIN2 cannot exceed 0.7V. This
necessitates additional circuitry to divide down the
input signal. See Figure 26 for an example circuit that
divides down backlight VDD to work properly with the
AIN1 pin.
Optical Reflectometry Application with
Dual LED and Single Photodiode
Figure 27 illustrates the MAX1358B in a complete opti-
cal reflectometry application with two transmitting LEDs
and one receiving photodiode. The LEDs transmit light
at a specific wavelength onto the sample strip, and the
photodiode receives the reflections from the strip. Set
the DAC to provide appropriate bias currents for the
LEDs. Always keep the photodiodes reverse-biased or
zero-biased. SPDT1 and SPDT2 switch between the
two LEDs.
Electrochemical Sensor Operation
The MAX1358B family interface with electrochemical
sensors. The 10-bit DAC with the force-sense buffers
have the flexibility to connect to many different types of
sensors. An external precision resistor completes the
transimpedance amplifier configuration to convert the
current generated by the sensor to a voltage measure-
ment using the ADC. The induced error from this source
is negligible due to FBA’s extremely low input bias cur-
rent. Internally, the ADC can differentially measure
directly across the external transimpedance resistor,
RF, eliminating any errors due to voltages drifting over
time, temperature, or supply voltage.
Temperature Measurement with
Two Remote Sensors
Use two diode-connected 2N3904 transistors for exter-
nal temperature sensing in Figure 29. Select AIN1 and
AIN2 through the positive and negative mux, respec-
tively. For internal temperature sensor measurements,
set MUXP<3:0> to 0111, and set MUXN<3:0> to 0000.
The analog input signals feed through a PGA to the
ADC for conversion.
The MAX1358B integrated PWM is available for LCD
bias control, sensor-bias voltage trimming, buzzer drive,
and duty-cycled sleep-mode power-control schemes.
Figure 30 shows the MAX1358B performing LCD bias
control. A sensor-bias voltage trimming application is
shown in Figure 31. Figures 33 and 34 show the PWM
circuitry being used in a single-ended and differential
piezoelectric buzzer-driving application.
ADC Calibration
Internal to the MAX1358B, the ADC is 24 bits and is
always in bipolar mode. The OFFSET CAL and GAIN
CAL data is also 24 bits. The conversion to unipolar and
the gain are performed digitally. The default values for
the OFFSET CAL and GAIN CAL registers in the
MAX1358B are 00 0000h and 80 0000h, respectively.
The calibration works as follows:
ADC = (RAW - OFFSET) x Gain x PGA
where ADC is the conversion result in the DATA register,
RAW is the output of the decimation filter internal to the
MAX1358B, OFFSET is the value stored in the OFFSET
CAL register, Gain is the value stored in the GAIN CAL
register, and PGA is the selected PGA gain found in the
ADC register as GAIN<1:0>. In unipolar mode, all nega-
tive values return a zero result and an additional gain of 2
is added.
相關PDF資料
PDF描述
V375B24M300BL CONVERTER MOD DC/DC 24V 300W
VI-20J-MY-S CONVERTER MOD DC/DC 36V 50W
MAX1340BETX+T IC ADC/DAC 12BIT W/FIFO 36WQFN
VI-25Z-MY-S CONVERTER MOD DC/DC 2V 20W
LTC6903IMS8#PBF IC OSC SILICON 68MHZ 8-MSOP
相關代理商/技術參數
參數描述
MAX1358BETL+ 功能描述:數據轉換系統 16-Bit 2Ch .512ksps 3.6V Precision SoIC RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX1358BETL+T 功能描述:數據轉換系統 16-Bit 2Ch .512ksps 3.6V Precision SoIC RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX1358BETL+TW 功能描述:模數轉換器 - ADC 16-Bit 2Ch .512ksps 3.6V Precision SoIC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1358BETL+W 功能描述:模數轉換器 - ADC 16-Bit 2Ch .512ksps 3.6V Precision SoIC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1358BETL-T 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*