- 您現在的位置：買賣IC網 > PDF目錄9466 > MAX1340BETX+T (Maxim Integrated Products)IC ADC/DAC 12BIT W/FIFO 36WQFN PDF資料下載
參數資料
| 型號： | MAX1340BETX+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 26/39頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC/DAC 12BIT W/FIFO 36WQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | ADC，DAC |
| 分辨率（位）： | 12 b |
| 采樣率（每秒）： | 225k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 36-TQFN 裸露焊盤（6x6） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
MAX1340/MAX1342/MAX1346/MAX1348
12-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
32
______________________________________________________________________________________
Externally Clocked Acquisitions and
Conversions Using the Serial Interface
ADC Conversions in Clock Mode 11
In clock mode 11, acquisitions and conversions are ini-
tiated by writing a command byte to the conversion
register and are performed one at a time using the
SCLK as the conversion clock. Scanning, averaging
and the FIFO are disabled, and the conversion result is
available at DOUT during the conversion. Output data
is updated on the rising edge of SCLK in clock mode
11. See Figure 9 for clock mode 11 timing.
Initiate a conversion by writing a command byte to the
conversion register followed by 16 SCLK cycles. If
CS
is pulsed high between the eighth and ninth cycles, the
pulse width must be less than 100s. To continuously
convert at 16 cycles per conversion, alternate 1 byte of
zeros (NOP byte) between each conversion byte. If 2
NOP bytes follow a conversion byte, the analog cells
power down at the end of the second NOP. Set the
FBGON bit to one in the reset register to keep the inter-
nal bias block powered.
If reference mode 00 is requested, or if an external refer-
ence is selected but a temperature measurement is being
requested, wait 45s with
CS high after writing the con-
version byte to extend the acquisition and allow the inter-
nal reference to power up. To perform a temperature
measurement, write 24 bytes (192 cycles) of zeros after
the conversion byte. The temperature result appears on
DOUT during the last 2 bytes of the 192 cycles.
Conversion-Time Calculations
The conversion time for each scan is based on a num-
ber of different factors: conversion time per sample,
samples per result, results per scan, if a temperature
measurement is requested, and if the external refer-
ence is in use. Use the following formula to calculate
the total conversion time for an internally timed conver-
sion in clock mode 00 and 10 (see the
Electrical
Characteristics, as applicable):
Total conversion time =
tCNV x nAVG x nSCAN + tTS + tINT-REF,SU
where:
tCNV = tDOV (where tDOV is dependent from the clock
and reference mode selected)
nAVG = samples per result (amount of averaging)
nSCAN = number of times each channel is scanned; set
to one unless [SCAN1, SCAN0] = 10
tTS = time required for temperature measurement
(58.1s); set to zero if temperature measurement is not
requested
tINT-REF,SU = tWU (external-reference wake-up); if a
conversion using the external reference is requested
In clock mode 01, the total conversion time depends on
how long
CNVST is held low or high. Conversion time in
externally clocked mode (CKSEL1, CKSEL0 = 11)
depends on the SCLK period and how long
CS is held
high between each set of eight SCLK cycles. In clock
mode 01, the total conversion time does not include the
time required to turn on the internal reference.
SCLK
DOUT
MSB1
LSB1
MSB2
(ACQUISITION1)
(ACQUISITION2)
(CONVERSION1)
DIN
(CONVERSION BYTE)
CS
EOC
X = DON'T CARE.
Figure 9. Clock Mode 11—Externally Timed Acquisition, Sampling, and Conversion without
CNVST
相關PDF資料 |
PDF描述 |
|---|---|
| VI-25Z-MY-S | CONVERTER MOD DC/DC 2V 20W |
| LTC6903IMS8#PBF | IC OSC SILICON 68MHZ 8-MSOP |
| LTC6903HMS8#PBF | IC OSC SILICON 68MHZ 8-MSOP |
| MAX1271BCAI+T | IC ADC 12BIT 8CH 28-SSOP |
| VI-25Z-MX-S | CONVERTER MOD DC/DC 2V 30W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13410EESA+ | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13410EESA+T | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13411EESA+ | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13411EESA+T | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13412EESA+ | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。