- 您現在的位置：買賣IC網 > PDF目錄2008 > MAX132EWG+T (Maxim Integrated Products)IC ADC 18BIT SERIAL 24-SOIC PDF資料下載
參數資料
| 型號： | MAX132EWG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 18BIT SERIAL 24-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 位數： | 18 |
| 采樣率（每秒）： | 100 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個偽差分，雙極 |
MAX132
±18-Bit ADC with Serial Interface
______________________________________________________________________________________
11
Averaging 2 or 3 read-zero measurements provides the
most accurate read-zero value. Perform a read-zero
sequence whenever a large change in the input voltage
is expected.
Sleep Bit
When the sleep bit is set to 1, (bit D5 in command input
register 0), the low-power sleep mode starts when EOC
returns high. In sleep mode, the supply current is typi-
cally 1A and the oscillator shuts down. The interface
remains active and data can be read. When exiting
sleep mode, the analog circuitry needs time to stabilize
before the next conversion starts. Accomplish this by
writing a dummy instruction to emerge from sleep
mode, and wait at least one conversion cycle before
writing a start instruction.
50Hz/60Hz
With a 32,768Hz crystal, the 50Hz/60Hz bit sets the
integrate period equal to one line cycle for 50Hz/60Hz
environments. When D6 (in command input register 0)
is set to 0, the integrate count is an integer multiple of
60Hz (32,768Hz/60Hz = 546 counts). When D6 is set to
1, the integrate input count is an integer multiple of
50Hz (32,768Hz/50Hz = 655 counts). Achieve the
greatest AC rejection by adjusting the integration peri-
od for 50Hz or 60Hz.
Start Conversion Bit
The start conversion bit (D7) in command input register
0 initiates a conversion when set to 1. The MAX132
immediately starts a conversion, stops at conversion
end, and then waits for the next start-bit command. A
start instruction is needed to initiate each conversion.
To initiate a continuous data stream, write a separate
start command for each conversion in three ways:
1) Wait longer than a known conversion time and then
write another start command.
2) Poll either the EOC status register bit or the EOC
line to determine conversion end and start time for
the next conversion. EOC becomes 1 at conversion
end at count 0000 of the conversion counter (Figure
10).
3) Set the start bit to 1 before a conversion end. The
internal conversion counter is then checked for its
count. If the count is 0000 (EOC = 1), a new conver-
sion starts and the conversion counter is set to
0001. The start bit resets to 0 after 5 clock cycles.
The MAX132 will not check the start bit again until
the conversion counter returns to a 0000 count. This
means a start command can be given any time after
0005 internal conversion count; the next conversion
starts when the counter returns to 0000.
DE-1
DE-2
DE-3
DE-4
X8-1
X8-2
X8-3
ZERO INT
INT OUT
50Hz mode
INTEGRATE
264
545
655
38
145
679
MAX
545
MAX
SOFT
OVERRANGE
AREA
(SEE TEXT)
40
147
47
30
0001
0000
0111
INT START
RESET
60Hz
60Hz mode
659 667
CHOP
1600
1346
1638
1783
1823
1970
2017
2047
0000
RESET EVENTS
INTERNAL CONVERSION DATA LATCH
LATCH
EOC
Figure 10. Conversion Timing (Negative Input Shown)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX135EPI+ | IC ADC 15BIT PARALLEL 28-DIP |
| MAX1361MEUB+T | IC SYSTEM MON 10BIT 4CH 10-UMAX |
| MAX1364MEUB+T | IC SYSTEM MON 12BIT 4CH 10-UMAX |
| MAX1394ETB+T | IC ADC 8BIT 416KSPS 10-TDFN-EP |
| MAX1395ETB+T | IC ADC 10BIT 357KSPS 10-TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX132MRG | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1330 | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX13300EVKIT+ | 功能描述:音頻 IC 開發(fā)工具 MAX13300/01 EVAL KIT RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX13301AUM/V+ | 制造商:Maxim Integrated Products 功能描述:4-CHANNEL, AUTOMOTIVE CLASS D AUDIO AMPLIFIER - Rail/Tube |
| MAX13301AUM/V+T | 制造商:Maxim Integrated Products 功能描述:4-CHANNEL, AUTOMOTIVE CLASS D AUDIO AMPLIFIER - Tape and Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。