參數資料
型號： MAX1322ECM
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： ADC
英文描述： 8-/4-/2-Channel, 14-Bit, Simultaneous-Sampling ADCs with 10V, 5V, and 0 to +5V Analog Input Ranges
中文描述： 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48
封裝： 7 X 7 MM, 1.40 MM HEIGHT, MS-026BBC, TQFP-48
文件頁數： 14/27頁
文件大?。?/td> 255K
代理商： MAX1322ECM
M
8-/4-/2-Channel, 14-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
14
______________________________________________________________________________________
To improve the input-signal bandwidth under AC condi-
tions, drive the input with a wideband buffer (>50MHz)
that can drive the ADC’s input capacitance and settle
quickly. For example, the MAX4265 can be used for +5V
unipolar devices, or the MAX4350 can be used for ±5V
bipolar inputs.
The T/H aperture delay is typically 13ns. The aperture-
delay mismatch between T/Hs of 50ps allows the relative
phase information of up to eight different inputs to be
preserved. Figure 2 shows a simplified equivalent input
circuit, illustrating the ADC’s sampling architecture.
Input Bandwidth
The input tracking circuitry has a 12MHz small-signal
bandwidth, making it is possible to digitize high-speed
transient events and measure periodic signals with
bandwidths exceeding the ADC’s sampling rate by using
undersampling techniques. To avoid high-frequency
signals being aliased into the frequency band of interest,
anti-alias filtering is recommended.
Input Range and Protection
These devices provide ±10V, ±5V, or 0 to +5V analog
input voltage ranges. Figure 2 shows the equivalent input
circuit. Overvoltage protection circuitry at the analog
input provides ±16.5V fault protection for the bipolar input
devices and ±6.0V fault protection for the unipolar input
devices. This fault-protection circuit limits the current
going into or out of the device to less than 50mA, provid-
ing an added layer of protection from momentary over-
voltage or undervoltage conditions at the analog input.
Power-S aving Modes
Shutdown Mode
During shutdown, the analog and digital circuits in the
device power down and the device draws less than
100μA from AV
DD
, and less than 100μA from DV
DD
.
Select shutdown mode using the SHDN input. Set SHDN
high to enter shutdown mode. After coming out of shut-
down, allow a 1ms wake-up time before making the first
conversion. When using an external clock, apply at least
20 clock cycles with CONVST high before making the first
conversion. When using internal-clock mode, wait at least
2μs before making the first conversion.
ALLON
ALLON is useful when some of the analog input channels
are selected (see the
Configuration Register
section).
Drive ALLON high to power up all input channel circuits,
regardless of whether they are selected as active by the
configuration register. Drive ALLON low or connect to
ground to power only the input channels selected as
active by the configuration register, saving 2mA per
channel (typ). The wake-up time for any channel turned
on with the configuration register is 2μs (typ) when
ALLON is low. The wake-up time with ALLON high is
only 0.01μs. New configuration-register information
does not become active until the next CONVST falling
edge. Therefore, when using software to control power
states (ALLON = 0), pulse CONVST low once before
applying the actual CONVST signal (Figure 3). With an
external clock, apply at least 15 clock cycles before
the second CONVST. If using internal-clock mode, wait
at least 1.5μs or until the first
EOC
before generating
the second CONVST.
Figure 2. Typical Input Circuit
CH_
R1
R2
V
BIAS
C
PAR
1pF
5pF
MAX1316–MAX1318
MAX1320–MAX1322
MAX1324–MAX1326
INPUT RANGE (V)
0 TO+5
±
5
±
10
R1 (k
)
3.33
6.67
13.33
R2 (k
)
5.00
2.86
2.35
V
BIAS
(V)
0.90
2.50
2.06
Table 1. Conversion Times Using the
Internal Clock
NUMBER OF CHANNELS
INTERNAL-CLOCK
CONVERSION TIME
1
2
3
4
5
6
7
8
1.6
1.9
2.2
2.5
2.8
3.1
3.4
3.7
相關PDF資料
PDF描述
MAX1324ECM 8-/4-/2-Channel, 14-Bit, Simultaneous-Sampling ADCs with 10V, 5V, and 0 to +5V Analog Input Ranges
MAX1325ECM 8-/4-/2-Channel, 14-Bit, Simultaneous-Sampling ADCs with 10V, 5V, and 0 to +5V Analog Input Ranges
MAX1317ECM 18-Bit Buffers/Drivers With 3-State Outputs 56-SSOP -40 to 85
MAX1320ECM Dual 8-Bit To 9-Bit Parity Bus Transceivers 56-SSOP -40 to 85
MAX132CNG 【18-Bit ADC with Serial Interface
相關代理商/技術參數
參數描述
MAX1322ECM+ 功能描述:模數轉換器 - ADC 14-Bit 2Ch 526ksps 3V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1322ECM+T 功能描述:模數轉換器 - ADC 14-Bit 2Ch 526ksps 3V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1322ECM-T 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX13234EAUP+ 功能描述:RS-232接口集成電路 3-5.5V 250Kbps RS232 Line Driver/Receiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX13234EAUP+T 功能描述:RS-232接口集成電路 3-5.5V 250Kbps RS232 Line Driver/Receiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*