with Internal Temperature Sensor and VDD
參數資料
型號: MAX1254BEUE+T
廠商: Maxim Integrated Products
文件頁數: 19/29頁
文件大?。?/td> 0K
描述: IC ADC 12BIT W/REF 16-TSSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
位數: 12
采樣率(每秒): 94k
數據接口: MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 15mW
電壓電源: 模擬和數字,雙 ±
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 16-TSSOP
包裝: 帶卷 (TR)
輸入數目和類型: 8 個單端,單極;8 個單端,雙極;4 個差分,單極;4 個差分,雙極
MAX1253/MAX1254
Stand-Alone, 10-Channel, 12-Bit System Monitors
with Internal Temperature Sensor and VDD Monitor
26
______________________________________________________________________________________
Automatic Reference Shutdown
The MAX1253/MAX1254 enter an automatic shutdown
mode when in reference mode 00 or when the sample
wait is greater than 80s in reference mode 01. Using
either of these reference modes and a sample wait
period as long as the application allows results in the
lowest power consumption.
Temperature Measurement
The MAX1253/MAX1254 support both single-ended
and differential temperature measurements. The design
decision between the two types of measurements
depends on the desired level of accuracy and on type
and/or number of temperature sensors. The superior
common-mode rejection and lower noise of the differ-
ential mode reduces measurement errors and provides
higher accuracy, while single-ended measurements
require a lower number of connections, resulting in a
simpler implementation and a higher number of moni-
tored points for each MAX1253/MAX1254.
Differential Temperature Measurement
Connect the anode of a diode-connected transistor to
the even input channel and the cathode to the odd
input channel of an input pair configured for differential
temperature measurement (AIN0/AIN1, AIN2/AIN3,
AIN4/AIN5, or AIN6/AIN7). Run the two sensor connec-
tion lines parallel to each other with minimum spacing.
This improves temperature measurement accuracy by
minimizing the differential noise between the two lines,
since they have equal exposure to most sources of
noise. For further improved noise rejection, shield the
two sensor connections by running them between
ground planes, when available.
Configure the MAX1253/MAX1254 inputs for differential
temperature measurement in the input configuration
register (see Tables 9 and 10) and enable the even
channel number in the channel enable register (see
Table 4).
Single-Ended Temperature Measurement
Connect the anode of a diode-connected transistor to
the input channel and the cathode to ground. Choose
ground connections for sensors away from high-current
return paths to avoid the introduction of errors caused by
voltage drops in the board/system ground, which is the
main drawback for single-ended measurements.
Practical options for better accuracy are the use of a
star-configured subsystem ground or a signal ground
plane; to isolate the anode sensor connection trace away
from board and system noise sources; or to shield it with
ground lines and ground planes (when available) to pre-
vent accuracy degradation in the temperature measure-
ments caused by magnetic/electric noise induction.
Configure the MAX1253/MAX1254 input used for single-
ended temperature measurement in the input configura-
tion register (see Tables 9 and 10) and enable the analog
input in the channel-enable register (see Table 4).
Remote Temperature Sensor Selection
Temperature-sensing accuracy depends on having a
good-quality, diode-connected, small-signal transistor
as a sensor. Accuracy has been experimentally verified
for 2N3904-type devices. The transistor must be a
small-signal type with low base resistance. Tight speci-
fications for forward current gain (+50 to +150, for
example) indicate that the manufacturer has good
process controls and that the devices have consistent
VBE characteristics. CPU on-board sensors and other
ICs’ on-board temperature-sensing devices can also
be used (see Table 16 for recommended devices).
Table 16. Remote Sensor Transistor
Manufacturers
MANUFACTURER
MODEL NUMBER
Central Semiconductor (USA)
CMPT3904
Fairchild Semiconductors (USA)
MMBT3904
Motorola (USA)
MMBT3904
Rohm Semiconductor (Japan)
SST3904
Siemens (Germany)
SMB3904
Zetex (England)
FMMT3904CT-ND
Diodes Inc.
MMBT3904
OUTPUT CODE
FULL-SCALE
TRANSITION
11....111
0
INPUT VOLTAGE (LSB)
ZS = 0
FS = VREF
11....110
11....101
00....011
00....010
00....001
00....000
2
13
FS
1 LSB =
VREF
4096
FS = 3/2 LSB
Figure 10. Unipolar Transfer Function, Full Scale (FS) = VREF
相關PDF資料
PDF描述
D38999/24MC98PB CONN RCPT 10POS JAM NUT W/PINS
MS27499E12A98PB CONN RCPT 10POS BOX MNT W/PINS
IDT723662L15PF8 IC FIFO BI SYNC 8192X36 120QFP
HIN211ECBZ IC 4DRVR/5RCVR RS232 5V 28-SOIC
VE-2WR-MX-F2 CONVERTER MOD DC/DC 7.5V 75W
相關代理商/技術參數
參數描述
MAX1254EVC16 功能描述:模數轉換器 - ADC Stand-Alone 10-Channel 12-Bit System Monitors with Internal Temperature Sensor and VDD Monitor RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1254EVKIT 功能描述:數據轉換 IC 開發工具 Evaluation Kit/Evaluation System for the MAX1254 MAX1253 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX12553ETL 制造商:Maxim Integrated Products 功能描述:14-BIT, 65MSPS, 3.3V ADC - Bulk
MAX12553ETL+ 制造商:Maxim Integrated Products 功能描述:ADC SGL PIPELINED 65MSPS 14BIT PARALLEL 40TQFN - Rail/Tube
MAX12553ETL+T 制造商:Maxim Integrated Products 功能描述:ADC SGL PIPELINED 65MSPS 14BIT PARALLEL 40TQFN - Tape and Reel