參數資料
型號: MAX1234ETI+
廠商: Maxim Integrated Products
文件頁數: 28/44頁
文件大?。?/td> 0K
描述: IC CNTRLR TOUCH 28-TQFN
其它有關文件: Automotive Product Guide
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 60
類型: 電阻
觸摸面板接口: 4 線
輸入數/鍵: 1,4 x 4 小鍵盤
分辨率(位): 8,10,12 b
數據接口: MICROWIRE?,QSPI?,串行,SPI?
數據速率/采樣率 (SPS,BPS): 50k
電壓基準: 內部
電源電壓: 4.75 V ~ 5.25 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 28-TQFN 裸露焊盤
供應商設備封裝: 28-TQFN-EP(5x5)
包裝: 管件
MAX1233/MAX1234
±15kV ESD-Protected Touch-Screen
Controllers Include DAC and Keypad Controller
34
______________________________________________________________________________________
Battery Voltage, Auxiliary Input, and
Temperature Input Scan
Use this scan to make periodic measurements of both
battery inputs, both auxiliary inputs, and both tempera-
ture inputs. The respective data registers have the lat-
est results at the end of each cycle. Thus, a single write
by the host to the MAX1233/MAX1234 ADC control reg-
ister results in six different measurements being made.
Figure 20 shows this scan operation.
Touch-Initiated Screen Scans
(PENSTS = 1; ADSTS = 0)
In the touch-initiated screen-scan mode, the
MAX1233/MAX1234 automatically perform a touch-
screen scan upon detecting a screen touch. The touch-
screen scans performed are determined by the
[A/D3:A/D0] written to the ADC control register. Figure
21 shows the flowchart for a complete touch-initiated X-
and Y- coordinate scan. Selection of resolution, conver-
sion rate, averaging, and touch-screen settling time
determine the overall conversion time.
Figure 22 shows the complete flowchart for a touch-
initiated X, Y, and Z scan.
Table 38 shows ADSTS Bit Operation.
Host-Initiated Screen Scans
(PENSTS = ADSTS = 0)
In this mode, the host processor decides when a touch-
screen scan begins. The MAX1233/MAX1234 detect a
screen touch and drive
PENIRQ LOW. The host recog-
nizes the interrupt request and can choose to write to
the ADC control register to select a touch-screen scan
function (PENSTS = ADSTS = 0). Figures 23 and 24
show the process of a host-initiated screen scan.
Key-Press Initiated Debounce Scan
(KEYSTS1 = 1, KEYSTS0 =0)
In the key-press initiated debounce mode, the
MAX1233/MAX1234 automatically perform a debounce
upon detecting a key press. Key scanning begins once
a key press has been detected and ends when a key
press has been debounced (Figures 25 and 9a).
Host-Initiated Debounce Scan
In this mode, the host processor decides when a
debounce scan begins. The MAX1233/MAX1234 detect
a key press and drive KEYIRQ low. The host processor
recognizes the interrupt request and can choose to
write to the keypad control register to initiate a
debounce scan (Figures 26 and 9b).
Keypad Debouncing
Keys are debounced either when (1) a key press has
been detected, or (2) when commanded by the host MPU.
The keys scanned by the keypad row and column pins
are debounced for a period of time (debounce period)
as determined by bits [DBN2:DBN0] of the keypad con-
trol register.
The keypad controller continues scanning until the keypad
stays in the same state for an entire debounce period.
Keypad Data
Keypad data can be read out of either the keypad data
status register (maskable), or the keypad data pending
register (not maskable). The keypad mask register is
used to mask individual keys in the keypad data status
register.
GPIO Control
Write to bits [GP7:GP0] of the GPIO control register to
configure one or more of the R_/C_pins as a GPIO pin.
Write to bits [OE7:OE0] of the GPIO control register to
configure the pins as an input or an output. GPIO data
can be read from or written to the GPIO data register. A
read returns the logic state of the GPIO pin. A write sets
the logic state of a GPIO output pin. Writing to a GPIO
input pin has no effect.
GPIO Pullup Disable Register
When programmed as GPIO output, by default, the
GPIO pins are active CMOS outputs. Write a 1 to the
pullup disable register to configure the GPIO output as
an open-drain output.
Using the 8-Bit DAC for LCD/TFT
Contrast Control
Design Example:
The 8-bit DAC offers the ability to control biasing of
LCD/TFT screens. In the circuit of Figure 27, it is
desired to have the MAX1677 DC-DC converter’s VOUT
to be adjustable.
The minimum and maximum DAC voltages (VDAC(HIGH)
and VDAC(LOW)) can be found in the Electrical
Characteristics table.
The output voltage of the MAX1677 (VOUT) can be cal-
culated by noting the following equations:
VOUT = VREFDAC + i1R1
[Equation 1]
i1 = i2 + i3
[Equation 2]
i2 = VREFDAC / R2
[Equation 3]
i3 = (VREFDAC - VDAC) / R3
[Equation 4]
Substituting equations 2, 3, and 4 into equation 1
yields:
VOUT = VREFDAC + (R1 / R2) VREF + (R1 / R3)
(VREFDAC - VDAC)
[Equation 5]
相關PDF資料
PDF描述
VI-B4H-MW-F1 CONVERTER MOD DC/DC 52V 100W
VI-B4F-MW-F4 CONVERTER MOD DC/DC 72V 100W
V24B3V3M100B CONVERTER MOD DC/DC 3.3V 100W
MAX11800ETC/V+ IC TOUCH SCREEN CTRLR LP 12WQFN
MC100EP16VTDTR2 IC RCVR/DRVR ECL DIFF VAR 8TSSOP
相關代理商/技術參數
參數描述
MAX1234ETI+ 功能描述:觸摸屏轉換器和控制器 4Ch uWire QSPI/SPI Touch Interface RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX1234ETI+T 功能描述:觸摸屏轉換器和控制器 4Ch uWire QSPI/SPI Touch Interface RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX1234EVC16 功能描述:數據轉換 IC 開發工具 MAX1233/34 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX1234EVKIT 制造商:Maxim Integrated Products 功能描述:+15KV ESD-PROTECTED TOUCH-SCREEN CO - Rail/Tube
MAX1236EUA 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32