- 您現在的位置：買賣IC網 > PDF目錄9918 > MAX1204BEAP+T (Maxim Integrated Products)IC ADC 10BIT 8CH 20-SSOP PDF資料下載
參數資料
| 型號： | MAX1204BEAP+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 8CH 20-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 位數： | 10 |
| 采樣率（每秒）： | 133k |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 640mW |
| 電壓電源： | 雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁
MAX1204
5V, 8-Channel, Serial, 10-Bit ADC
with 3V Digital Interface
12
Maxim Integrated
Simple Software Interface
Make sure the CPU’s serial interface runs in master
mode so the CPU generates the serial clock. Choose a
clock frequency from 100kHz to 2MHz.
1) Set up the control byte for external clock mode and
call it TB1. TB1’s format should be: 1XXXXX11 binary,
where the Xs denote the particular channel and
conversion mode selected.
2) Use a general-purpose I/O line on the CPU to pull
CS on the MAX1204 low.
3) Transmit TB1 and simultaneously receive a byte
and call it RB1. Ignore RB1.
4) Transmit a byte of all zeros ($00 hex) and simulta-
neously receive byte RB2.
5) Transmit a byte of all zeros ($00 hex) and simulta-
neously receive byte RB3.
6) Pull CS on the MAX1204 high.
Figure 6 shows the timing for this sequence. Bytes RB2
and RB3 contain the result of the conversion padded
with one leading zero, two trailing sub-bits (S1 and S0),
and three trailing zeros. Total conversion time is a func-
tion of the serial clock frequency and the amount of idle
time between 8-bit transfers. To avoid excessive T/H
droop, make sure that the total conversion time does
not exceed 120s.
Digital Output
In unipolar input mode, the output is straight binary
(Figure 15); for bipolar inputs, the output is two’s-
complement (Figure 16). Data is clocked out at SCLK’s
falling edge in MSB-first format. The digital output logic
level is adjusted with the VL pin. This allows DOUT and
SSTRB to interface with 3V logic without the risk of
overdrive. The MAX1204’s digital inputs are designed
to be compatible with 3V CMOS logic as well as 5V
logic.
Internal and External Clock Modes
The MAX1204 can use either an external serial clock
or the internal clock to perform the successive-
approximation conversion. In both clock modes, the
external clock shifts data in and out of the MAX1204.
The T/H acquires the input signal as the last three bits
of the control byte are clocked into DIN. Bits PD1 and
PD0 of the control byte program the clock mode.
Figures 7–10 show the timing characteristics common
to both modes.
External Clock
In external clock mode, the external clock not only shifts
data in and out, but it also drives the A/D conversion
steps. SSTRB pulses high for one clock period after the
last bit of the control byte. Successive-approximation bit
decisions are made and appear at DOUT on each of the
next 12 SCLK falling edges (Figure 6). SSTRB and
DOUT go into a high-impedance state when CS goes
high; after the next CS falling edge, SSTRB outputs a
logic low. Figure 8 shows the SSTRB timing in external
clock mode.
The conversion must complete in some minimum time or
droop on the sample-and-hold can degrade conversion
results. Use internal clock mode if the clock period
exceeds 10s or if serial-clock interruptions could cause
the conversion interval to exceed 120s.
Internal Clock
In internal clock mode, the MAX1204 generates its own
conversion clock. This frees the P from running the
SAR conversion clock, and allows the conversion
results to be read back at the processor’s convenience,
at any clock rate from zero to 2MHz. SSTRB goes low
at the start of the conversion, then goes high when the
conversion is complete. SSTRB is low for a maximum of
10s, during which time SCLK should remain low for
best noise performance. An internal register stores data
while the conversion is in progress. SCLK clocks the
data out at this register at any time after the conversion
is complete. After SSTRB goes high, the next falling
clock edge produces the MSB of the conversion at
DOUT, followed by the remaining bits in MSB-first for-
mat (Figure 9). CS does not need to be held low once a
conversion is started. Pulling CS high prevents data
from being clocked into the MAX1204 and three-states
DOUT, but it does not adversely affect an internal
clock-mode conversion already in progress. When
internal clock mode is selected, SSTRB does not go
high impedance when CS goes high.
Figure 10 shows the SSTRB timing in internal clock
mode. Data can be shifted in and out of the MAX1204 at
clock rates up to 2.0MHz if the acquisition time, tACQ, is
kept above 1.5s.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2WM-MX-F4 | CONVERTER MOD DC/DC 10V 75W |
| ISL32177EFRZ-T | IC RCVR RS485/422 QD ESD 24QFN |
| MAX1204ACAP+T | IC ADC 10BIT 8CH 20-SSOP |
| VI-2WM-MX-F3 | CONVERTER MOD DC/DC 10V 75W |
| ISL32175EIVZ-T | IC RCVR RS485/422 QD ESD 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1204BEPP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1204BEPP+ | 功能描述:模數轉換器 - ADC 10-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1204BMJP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1205CMH | 制造商:Maxim Integrated Products 功能描述:44 PINS MQFP PKG - Bulk |
| MAX1205CMH+ | 制造商:Maxim Integrated Products 功能描述:ADC SGL PIPELINED 1MSPS 14BIT PARALLEL 44MQFP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。