- 您現在的位置：買賣IC網 > PDF目錄385520 > MAX110 (Maxim Integrated Products, Inc.) Low-Cost, 2-Channel, 4-Bit Serial ADCs(±5V，2通道，±14位串行模數轉換器) PDF資料下載
參數資料
| 型號： | MAX110 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Low-Cost, 2-Channel, 4-Bit Serial ADCs(±5V，2通道，±14位串行模數轉換器) |
| 中文描述： | 低成本、2通道、±14位串行ADC |
| 文件頁數： | 15/24頁 |
| 文件大?。?/td> | 286K |
| 代理商： | MAX110 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
M
Low-Cost, 2-Channel, ±14-Bit S erial ADCs
______________________________________________________________________________________
15
NO-OP
is a zero, the control word is not transferred to
the control register, the ADC’s configuration remains
unchanged, and no new conversion is initiated. This
allows specific ADCs in a “daisy chain” arrangement to
be reconfigured while leaving the remaining ADCs
unchanged. Table 1 lists the various ADC control word
functions.
Output data is shifted out of DOUT at the same time the
input control word for the next conversion is shifted in
(Figure 8).
On power-up, all internal registers reset to zero.
Therefore, when writing the first control word to the
ADC, the data simultaneously shifted out will be zeros.
The first conversion begins when
CS
goes high (
NO-OP
= 1). The results are placed in the 16-bit I/O register for
access on the next data-transfer operation.
Power-Down Mode
Bits 0 and 1 control the ADC’s power-down mode. If bit
0 (PD) is a logic high, power is removed from all analog
circuitry except the RC oscillator. A logic high at bit 1
(PDX) removes power from the RC oscillator. If both bits
PD and PDX are a logic high, or if PD is high and
RCSEL is low, the supply currents reduce to 4μA. If an
external XCLK clock continues to run in power-down
mode, the supply current will depend on the clock rate.
When PDX is set high, the internal RC oscillator stops
shortly after
CS
returns high. If the next control word
written to the device has
NO-OP
= 1 instructing the
ADC to convert, BUSY will go low, but because the RC
oscillator is stopped, BUSY will remain low and will not
allow a new conversion to begin. To avoid this situation,
write a “dummy” control word with
NO-OP
= 0 and any
combination of bits 14-0 in the control word following
the control word with PDX = 0. With
NO-OP
= 0, bits 14-
0 are ignored and the internal state machine resets.
Next, perform a normal 3-step calibration (see Table 3).
Note that XCLK must be connected to V
DD
or GND
through a resistor (suggested value is 1M
) when the
RC oscillator mode is selected (RCSEL = V
DD
). This
resistor is not necessary if the external oscillator mode
is used, or if the internal oscillator is not shut down.
S elec ting the Analog Inputs
Bit 4 (CHS) controls which of the two differential inputs
connect to the internal ADC inputs (see the Functional
Diagram. A logic high selects IN2+ and IN2- while a
logic low selects IN1+ and IN1-. Table 2 shows the
allowable input multiplexer configurations.
Table 1. Input Control-Word Bit Map
↑
First bit clocked in.
PD
PDX
NUL
CAL
CHS
NU
NU
DV2
DV4
CONV1
CONV2
CONV3
CONV4
NU
NU
NO-OP
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Analog Power-Down. Set this bit high to power down the analog section.
PD
0
Oscillator Power-Down. Set this bit high to power down the RC oscillator.
PDX
1
Internal Offset-Null Bit. A logic high selects offset-null mode. See Table 3.
NUL
2
Gain-Calibration Bit. A logic high selects gain-calibration mode. See Table 3.
CAL
3
Input Channel Select. A logic high selects channel 2 (IN2+ and IN2-), while a logic low
selects channel 1 (IN1+ and IN1-). See Tables 2 and 3.
CHS
4
XCLK to Oversampling Cock Ratio Control Bits. See Table 5.
DV2, DV4
7, 8
Conversion Time Control Bits. See Table 4.
CONV1–CONV4
9–12
Used for test purposes only. Set these bits low.
NU
5, 6, 13, 14
If this bit is a logic high, the remaining 15 LSBs are transferred to the control register and a
new conversion begins when
CS
returns high. If this bit is set low, the control word is not
passed to the control register, the ADC configuration remains unchanged, and no new con-
version begins when
CS
returns high.
NO-OP
15
DESCRIPTION
NAME
BIT
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1126 | Quad, 12-Bit, 40Msps, 1.8V ADC with Serial LVDS Outputs |
| MAX1126EGK | Quad, 12-Bit, 40Msps, 1.8V ADC with Serial LVDS Outputs |
| MAX11504 | Four-Channel, Standard-Definition Video Filter |
| MAX11505 | Four-Channel, Standard-Definition Video Filter |
| MAX1168EVC16 | MAX1168 Evaluation Kit/Evaluation System |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11008 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual RF LDMOS Bias Controller with Nonvolatile Memory |
| MAX11008BETM+ | 功能描述:射頻放大器 Dual RF LDMOS Bias Controller w/NV Mem RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX11008BETM+T | 功能描述:射頻放大器 Dual RF LDMOS Bias Controller w/NV Mem RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX11008EVC16 | 功能描述:放大器 IC 開發工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX11008EVKIT+ | 功能描述:放大器 IC 開發工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。