- 您現在的位置：買賣IC網 > PDF目錄10588 > MAX1037EKA+T (Maxim Integrated Products)IC ADC 8-BIT 188KSPS SOT23-8 PDF資料下載
參數資料
| 型號： | MAX1037EKA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 8-BIT 188KSPS SOT23-8 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 位數： | 8 |
| 采樣率（每秒）： | 188k |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 1.15mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-8 |
| 供應商設備封裝： | SOT-23-8 |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個偽差分，單極；2 個偽差分，雙極 |
| 產品目錄頁面： | 1395 (CN2011-ZH PDF) |
| 其它名稱： | MAX1037EKA+TDKR |
MAX1036–MAX1039
Applications Information
Power-On Reset
The configuration and setup registers (Tables 1 and 2)
default to a single-ended, unipolar, single-channel con-
version on AIN0 using the internal clock with VDD as the
reference and AIN_/REF configured as an analog input.
The RAM contents are unknown after power-up.
Automatic Shutdown
SEL[2:0] of the setup byte (Tables 1 and 6) controls the
state of the reference and AIN_/REF. If automatic shut-
down is selected (SEL[2:0] = 100), shutdown occurs
between conversions when the MAX1036–MAX1039 are
idle. When operating in external clock mode, a STOP
condition must be issued to place the devices in idle
mode and benefit from automatic shutdown. A STOP
condition is not necessary in internal clock mode to ben-
efit from automatic shutdown because power-down
occurs once all contents are written to memory (Figure
10). All analog circuitry is inactive in shutdown and sup-
ply current is less than 1A. The digital conversion
results are maintained in RAM during shutdown and are
available for access through the serial interface at any
time prior to a STOP or repeated START condition.
When idle, the MAX1036–MAX1039 wait for a START
condition followed by their slave address (see the
Slave Address section). Upon reading a valid address
byte, the MAX1036–MAX1039 power up. The analog
circuits do not require any wakeup time from shutdown,
whether using external or internal reference.
Automatic shutdown results in dramatic power savings,
particularly at slow conversion rates. For example, at a
conversion rate of 10ksps, the average supply current
for the MAX1036 is 8A and drops to 2A at 1ksps.
At 0.1ksps the average supply current is just 1A (see
Average Supply Current vs. Conversion Rate in the
Typical Operating Characteristics section).
Reference Voltage
SEL[2:0] of the setup byte (Table 1) controls the refer-
ence and the AIN_/REF configuration (Table 6). When
AIN_/REF is configured to be a reference input or refer-
ence output (SEL1 = 1), conversions on AIN_/REF
appear as if AIN_/REF is connected to GND (see Note
2 of Tables 3 and 4).
Internal Reference
The internal reference is 4.096V for the MAX1036/
MAX1038 and 2.048V for the MAX1037/MAX1039. SEL1
of the setup byte controls whether AIN_/REF is used for
an analog input or a reference (Table 6). When
AIN_/REF is configured to be an internal reference out-
put (SEL[2:1] = 11), decouple AIN_/REF to GND with a
0.01F capacitor. Due to the decoupling capacitor and
the 675Ω reference source impedance, allow 80s for
the reference to stabilize during initial power-up. Once
powered up, the reference always remains on until
reconfigured. The reference should not be used to sup-
ply current for external circuitry.
2.7V to 3.6V and 4.5V to 5.5V, Low-Power,
4-/12-Channel 2-Wire Serial 8-Bit ADCs
______________________________________________________________________________________
15
BIT 7
(MSB)
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
(LSB)
REG
SCAN1
SCAN0
CS3
CS2
CS1
CS0
SGL/DIF
BIT
NAME
DESCRIPTION
7
REG
Register bit. 1 = Setup Byte (Table 1), 0 = Configuration Byte.
6
SCAN1
5
SCAN0
Scan select bits. Two bits select the scanning configuration (Table 5). Default to 00 at
power-up.
4
CS3
3
CS2
2
CS1
1
CS0
Channel select bits. Four bits select which analog input channels are to be used for conversion
(Tables 3, 4). Default to 0000 at power-up. For MAX1036/MAX1037, CS3 and CS2 are internally
set to 0.
0
SGL/DIF
1 = single-ended, 0 = pseudo-differential (Tables 3, 4). Default to 1 at power-up (see the Single-
Ended/Pseudo-Differential Input section).
Table 2. Configuration Byte Format
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BTN-MX-F3 | CONVERTER MOD DC/DC 18.5V 75W |
| ISL59601IRZ-T7A | IC VIDEO EQUALIZER 20-QFN |
| VE-27P-IW-F2 | CONVERTER MOD DC/DC 13.8V 100W |
| VI-BTN-MX-F2 | CONVERTER MOD DC/DC 18.5V 75W |
| PT01A-8-4P | CONN RCPT 4 POS CBL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1037KEKA | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
| MAX1037KEKA+ | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 188KSPS 8BIT SERL 8PIN SOT-23 - Cut Tape Product |
| MAX1037KEKA+T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1037KEKA-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1037LEKA | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
發布緊急采購，3分鐘左右您將得到回復。