- 您現在的位置：買賣IC網 > PDF目錄45047 > M38869M8A-XXXGP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M38869M8A-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 0.65 MM PITCH, PLASTIC, QFP-80! |
| 文件頁數： | 85/113頁 |
| 文件大?。?/td> | 1871K |
| 代理商： | M38869M8A-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁
70
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
q Erase command
The erase command is executed by inputting command code 2016
in the first cycle and command code 2016 again in the second
cycle. The command code is latched into the internal command
___
latch at the rising edges of the WE input in the first cycle and in
the second cycle, respectively. The erase operation is initiated at
___
the rising edge of the WE input in the second cycle, and the
memory contents are collectively erased within 9.5 ms as mea-
sured by the internal timer. Note that data 0016 must be written to
all memory locations before executing the erase command.
Note: An erase operation is not completed by executing the erase
command once. Always be sure to execute an erase verify
command after executing the erase command. When the fail-
ure is found in this verification, the user must repeatedly ex-
ecute the erase command until the pass. Refer to Figure 71
for the erase flowchart.
Fig. 70 Input/output timings during erasing (verify data is output at the same timing as for read.)
q Erase verify command
The user must verify the contents of all addresses after complet-
ing the erase command. The microcomputer enters the erase
verify mode by inputting the verify address and command code
A016 in the first cycle. The address is internally latched at the fall-
___
ing edge of the WE input, and the command code is internally
___
latched at the rising edge of the WE input. When control signals
are input in the second cycle at the timing shown in Figure 70, the
M38869FFAHP/GP outputs the contents of the specified address
to the external.
Note: If any memory location where the contents have not been
erased is found in the erase verify operation, execute the op-
eration of “erase
→ erase verify” over again. In this case,
however, the user does not need to write data 0016 to memory
locations before erasing.
Address
Erase
Erase verify
Verify
address
tWC
tCS
tRRW
tWP
tWPH
tWP
tDE
tDS
2016
A016
Dout
tDS
tDH
Verify data output
tDH
tVSC
tDS
tWP
tWRR
tCS
tCH
tAS
tAH
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VPPH
VPPL
CE
OE
WE
Data
VPP
相關PDF資料 |
PDF描述 |
|---|---|
| M38867E8AHP | 8-BIT, OTPROM, 5 MHz, MICROCONTROLLER, PQFP80 |
| M38867E8A-XXXHP | 8-BIT, OTPROM, 5 MHz, MICROCONTROLLER, PQFP80 |
| M38869MFA-XXXGP | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80 |
| M38867M8A-XXXHP | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80 |
| M38869MCA-XXXHP | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38869M8A-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869M8-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869M9-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869MA-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869MB-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。