- 您現在的位置：買賣IC網 > PDF目錄45044 > M38227M8A-XXXHP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M38227M8A-XXXHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 12 X 12 MM, 0.50 MM PITCH, PLASTIC, LQFP-80 |
| 文件頁數： | 40/58頁 |
| 文件大小： | 733K |
| 代理商： | M38227M8A-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
45
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
3822 Group (A ver.)
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e param
etric
lim
its are
subject
to change.
(3) Oscillator concerns
In order to obtain the stabilized operation clock on the user system
and its condition, contact the oscillator manufacturer and select
the oscillator and oscillation circuit constants. Be careful espe-
cially when range of votage and temperature is wide.
Also, take care to prevent an oscillator that generates clocks for a
microcomputer operation from being affected by other signals.
Keeping oscillator away from large current signal lines
Install a microcomputer (and especially an oscillator) as far as
possible from signal lines where a current larger than the toler-
ance of current value flows.
q Reason
In the system using a microcomputer, there are signal lines for
controlling motors, LEDs, and thermal heads or others. When a
large current flows through those signal lines, strong noise oc-
curs because of mutual inductance.
Installing oscillator away from signal lines where potential levels
change frequently
Install an oscillator and a connecting pattern of an oscillator
away from signal lines where potential levels change frequently.
Also, do not cross such signal lines over the clock lines or the
signal lines which are sensitive to noise.
q Reason
Signal lines where potential levels change frequently (such as
the CNTR pin signal line) may affect other lines at signal rising
edge or falling edge. If such lines cross over a clock line, clock
waveforms may be deformed, which causes a microcomputer
failure or a program runaway.
Keeping oscillator away from large current signal lines
Installing oscillator away from signal lines where potential
levels change frequently
Fig. 47 Wiring for the VPP pin of One Time PROM
Fig. 46 Wiring for a large current signal line/Wiring of signal
lines where potential levels change frequently
P40/VPP
VSS
About 5k
(4) Analog input
The analog input pin is connected to the capacitor of a voltage
comparator. Accordingly, sufficient accuracy may not be obtained
by the charge/discharge current at the time of A-D conversion
when the analog signal source of high-impedance is connected to
an analog input pin. In order to obtain the A-D conversion result
stabilized more, please lower the impedance of an analog signal
source, or add the smoothing capacitor to an analog input pin.
(5) Difference of memory type and size
When Mask ROM and PROM version and memory size differ in
one group, actual values such as an electrical characteristics, A-D
conversion accuracy, and the amount of -proof of noise incorrect
operation may differ from the ideal values.
When these products are used switching, perform system evalua-
tion for each product of every after confirming product
specification.
(6) Wiring to VPP pin of One Time PROM version
Connect an approximately 5 k
resistor to the VPP pin the
shortest possible in series and also to the VSS pin.
Note: Even when a circuit which included an approximately 5 k
resistor is used in the Mask ROM version, the microcomputer
operates correctly.
q Reason
The VPP pin of the One Time PROM version is the power source
input pin for the built-in PROM. When programming in the built-in
PROM, the impedance of the VPP pin is low to allow the electric
current for writing flow into the built-in PROM. Because of this,
noise can enter easily. If noise enters the VPP pin, abnormal in-
struction codes or data are read from the built-in PROM, which
may cause a program runaway.
Electric Characteristic Differences Between
Mask ROM and One Time PROM Version MCUs
There are differences in electric characteristics, operation margin,
noise immunity, and noise radiation between Mask ROM and
One Time PROM version MCUs due to the difference in the manufac-
turing processes.
When manufacturing an application system with the One TIme PROM
version and then switching to use of the Mask ROM version,
please perform sufficient evaluations for the commercial
samples of the Mask ROM version.
XIN
XOUT
VSS
Microcomputer
Mutual inductance
Large
current
GND
M
XIN
XOUT
VSS
CNTR
Do not cross
N.G.
相關PDF資料 |
PDF描述 |
|---|---|
| M38224M6A-XXXFP | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80 |
| M38238G8HP | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 |
| M38234G4FP | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 |
| M38238G8-XXXHP | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 |
| M3823AGF-XXXHP | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38227RFS | 制造商:Renesas Electronics Corporation 功能描述:MCU - Trays |
| M3823 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 18AWG BLK 1000' |
| M3823 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 18AWG BLK 500' |
| M3823 BK005 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 18AWG BLK 100' |
| M38234G4FP#U0 | 功能描述:MCU 2/5V 16K 80-QFP QZ-ROM RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。