參數資料
型號: M38203M4-065FP
廠商: Mitsubishi Electric Corporation
元件分類: DC/DC變換器
英文描述: 1 watt dc-dc converters
中文描述: 1瓦的DC - DC轉換器
文件頁數: 23/66頁
文件大?。?/td> 1093K
代理商: M38203M4-065FP
23
MITSUBISHI MICROCOMPUTERS
3820 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Timer Y
Timer Y is a 16-bit timer that can be selected in one of four modes.
Timer mode
The timer counts f(X
IN
)/16 (or f(X
CIN
)/16 in low-speed mode).
Period measurement mode
CNTR
1
interrupt request is generated at rising/falling edge of
CNTR
1
pin input signal. Simultaneously, the value in timer Y latch
is reloaded in timer Y and timer Y continues counting down. /Ex-
cept for the above-mentioned, the operation in period measure-
ment mode is the same as in timer mode.
The timer value just before the reloading at rising/falling of CNTR
1
pin input signal is retained until the timer Y is read once after the
reload.
The rising/falling timing of CNTR
1
pin input signal is found by
CNTR
1
interrupt. When using a timer in this mode, set the corre-
sponding port P5
5
direction register to input mode.
Event counter mode
The timer counts signals input through the CNTR
1
pin.
Except for this, the operation in event counter mode is the same
as in timer mode. When using a timer in this mode, set the corre-
sponding port P5
5
direction register to input mode.
Pulse width HL continuously measurement mode
CNTR
1
interrupt request is generated at both rising and falling
edges of CNTR
1
pin input signal. Except for this, the operation in
pulse width HL continuously measurement mode is the same as in
period measurement mode. When using a timer in this mode, set
the corresponding port P5
5
direction register to input mode.
Note on CNTR
1
Interrupt Active Edge Selec-
tion
CNTR
1
interrupt active edge depends on the CNTR
1
active edge
switch bit. However, in pulse width HL continuously measurement
mode, CNTR
1
interrupt request is generated at both rising and
falling edges of CNTR
1
pin input signal regardless of the setting of
CNTR
1
active edge switch bit.
Fig. 13 Structure of timer Y mode register
Timer Y mode register
(TYM : address 0028
16
)
Not used (return "0" when read)
Timer Y operating mode bits
b5 b4
0 0 : Timer mode
0 1 : Period measurement mode
1 0 : Event counter mode
1 1 : Pulse width HL continuously
measurement mode
CNTR
1
active edge switch bit
CNTR
1
interrupt
0 : Falling edge active
1 : Rising edge active
Period measurement mode
0 : Measure falling edge to falling edge
1 : Measure rising edge to rising edge
Event counter mode
0 : Rising edge active
1 : Falling edge active
Timer Y stop control bit
0 : Count start
1 : Count stop
7
0
相關PDF資料
PDF描述
M38203M4-076FP 1 watt dc-dc converters
M38203M4-083FP 1 watt dc-dc converters
M38203M4-093FP 1 watt dc-dc converters
M38203N4-095FD 1 watt dc-dc converters
M38203M4-417HPDR 1 watt dc-dc converters
相關代理商/技術參數
參數描述
M38203M4-076FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38203M4-083FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38203M4-093FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38203M4-095FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38203M4-125FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER