- 您現在的位置：買賣IC網 > PDF目錄45040 > M38039MF-XXXHP 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M38039MF-XXXHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 134/136頁 |
| 文件大?。?/td> | 2007K |
| 代理商： | M38039MF-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁當前第134頁第135頁第136頁
97
3803/3804 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
q Program command
The microcomputer enters the program mode by inputting com-
mand code “4016” in the first cycle. The command code is latched
___
into the internal command latch at the rising edge of the WE input.
When the address which indicates a program location and data is
input in the second cycle, the M38039FF/M38049FF internally
___
latches the address at the falling edge of the WE input and the
___
data at the rising edge of the WE input. The M38039FF/
___
M38049FF starts programming at the rising edge of the WE input
in the second cycle and finishes programming within 10
s as
measured by its internal timer. Programming is performed in units
of bytes.
Note: A programming operation is not completed by executing the
program command once. Always be sure to execute a pro-
gram verify command after executing the program command.
When the failure is found in this verification, the user must re-
peatedly execute the program command until the pass. Refer
to Figure 92 for the programming flowchart.
q Program verify command
The microcomputer enters the program verify mode by inputting
command code “C016” in the first cycle. This command is used to
verify the programmed data after executing the program com-
mand. The command code is latched into the internal command
___
latch at the rising edge of the WE input. When control signals are
input in the second cycle at the timing shown in Figure 90, the
M38039FF/M38049FF outputs the programmed address’s con-
tents to the external. Since the address is internally latched when
the program command is executed, there is no need to input it in
the second cycle.
Fig. 90 Input/output timings during programming (Verify data is output at the same timing as for read.)
Address
Program
Program verify
Program
address
tWC
tCS
tRRW
tWP
tWPH
tWP
tDP
tDS
4016
DIN
C016
Dout
tDS
tDH
Verify data output
tDH
tVSC
tDS
tWP
tWRR
tCS
tCH
tAS
tAH
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VPPH
VPPL
CE
OE
WE
Data
VPP
相關PDF資料 |
PDF描述 |
|---|---|
| M38037M6H-XXXHP | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| M38037M8H-XXXSP | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PDIP64 |
| M38039FFHKP | 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| M38039MCH-XXXKP | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| M38039FFHHP | 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38049FFFP#U0 | 制造商:Renesas Electronics Corporation 功能描述: |
| M38049FFLHP#U0 | 制造商:Renesas Electronics Corporation 功能描述: |
| M38049RLSS | 功能描述:DEV EMULATOR CHIP RAM 2KB 64SDIP RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:* |
| M3806 | 功能描述:電纜固定件和配件 LTSCG 625 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: |
| M3806 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 1000' |
發布緊急采購，3分鐘左右您將得到回復。