- 您現在的位置：買賣IC網 > PDF目錄45035 > M37542M4-XXXHP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 PDF資料下載
參數資料
| 型號： | M37542M4-XXXHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 |
| 封裝： | 6 X 6 MM, 0.50 MM PITCH, PLASTIC, WQFN-36 |
| 文件頁數： | 20/122頁 |
| 文件大小： | 1311K |
| 代理商： | M37542M4-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
7542 Group
Rev.3.03
Jul 11, 2008
Page 116 of 117
REJ03B0006-0303
Notes on Clock Generating Circuit
1. Switch of ceramic and RC oscillations
After releasing reset, the oscillation mode selection bit (bit 5 of
CPU mode register (address 3B16)) is “0” (ceramic oscillation se-
lected). When the RC oscillation is used, after releasing reset, set
this bit to “1”.
2. Double-speed mode
The double-speed mode can be used only when a ceramic oscilla-
tion is selected. Do not use it when an RC oscillation is selected.
3. CPU mode register
Oscillation mode selection bit (bit 5), processor mode bits (bits 1
and 0) of CPU mode register (address 3B16) are used to select os-
cillation mode and to control operation modes of the
microcomputer. In order to prevent the dead-lock by erroneously
writing (ex. program run-away), these bits can be rewritten only
once after releasing reset. After rewriting, it is disabled to write any
data to the bit. (The emulator MCU “M37542RSS” is excluded.)
Also, when the read-modify-write instructions (SEB, CLB, etc.) are
executed to bits 2 to 4, 6 and 7, bits 5, 1 and 0 are locked.
4. Clock division ratio, XIN oscillation control, on-chip oscillator
control
The state transition shown in Fig. 84 can be performed by setting
the clock division ratio selection bits (bits 7 and 6), XIN oscillation
control bit (bit 4), on-chip oscillator oscillation control bit (bit 3) of
CPU mode register. Be careful of notes on use in Fig. 84.
5. On-chip oscillator operation
When the MCU operates by the on-chip oscillator for the main
clock, connect XIN pin to VCC through a 1 k to 10 k resistor and
leave XOUT pin open.
The clock frequency of the on-chip oscillator depends on the sup-
ply voltage and the operation temperature range.
Be careful that this margin of frequencies when designing applica-
tion products.
6. Ceramic resonator
When the ceramic resonator is used for the main clock, connect
the ceramic resonator and the external circuit to pins XIN and
XOUT at the shortest distance. Externally connect a damping resis-
tor Rd depending on the oscillation frequency. A feedback resistor
is built-in.
Use the resonator manufacturer’s recommended value because
constants such as capacitance depend on the resonator.
7. RC oscillation
When the RC oscillation is used for the main clock, connect the
XIN pin and XOUT pin to the external circuit of resistor R and the
capacitor C at the shortest distance.
The frequency is affected by a capacitor, a resistor and a micro-
computer.
So, set the constants within the range of the frequency limits.
8. External clock
When the external signal clock is used for the main clock, connect
the XIN pin to the clock source and leave XOUT pin open.
Select “0” (ceramic oscillation) to oscillation mode selection bit.
9. Count source (Timer 1, Timer A, Timer B, Timer X, Serial I/O,
Serial I/O2, A/D converter, Watchdog timer)
A count source of watchdog timer is affected by the clock divi-
sion selection bit of the CPU mode register.
The f(XIN) clock is supplied to the watchdog timer when select-
ing f(XIN) as the CPU clock.
The on-chip oscillator output is supplied to the watchdog timer
when selecting the on-chip oscillator output as the CPU clock.
Notes on Oscillation Control
1. Oscillation stop detection circuit
(1) When the stop mode is used, set the oscillation stop detection
function to “invalid”.
(2) When the ceramic or RC oscillation is stopped by the XIN oscil-
lation control bit (bit 4 of CPU mode register (address 3B16)),
set the oscillation stop detection function to “invalid”.
2. Stop mode
(1) When the stop mode is used, set the oscillation stop detection
function to “invalid”.
(2) When the stop mode is used, set “0” (STP instruction enabled)
to the STP instruction function selection bit of the watchdog
timer control register (bit 6 of watchdog timer control register
(address 3916)).
(3) The oscillation stabilizing time after release of STP instruction
can be selected from “set automatically ”/“not set automati-
cally” by the oscillation stabilizing time set bit after release of
the STP instruction (bit 0 of MISRG (address 3816)). When “0”
is set to this bit, “0116” is set to timer 1 and “FF16” is set to
prescaler 1 automatically at the execution of the STP instruc-
tion. When “1” is set to this bit, set the wait time to timer 1 and
prescaler 1 according to the oscillation stabilizing time of the
oscillation. Also, when timer 1 is used, set values again to
timer 1 and prescaler 1 after system is returned from the stop
mode.
(4) Do not execute the STP instruction during the A/D conversion.
相關PDF資料 |
PDF描述 |
|---|---|
| M37542M2-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| M37542M2-XXXHP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 |
| M37542M2-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37542F4SP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8HP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQCC36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37542M4-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542RSS | 功能描述:DEV EMULATION EVA CHIP FOR M3754 RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M37544 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37544G2AGP | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 8KB ROM 5V 32LQFP - Trays |
| M37544G2AGP#U0 | 功能描述:IC 740 MCU OTP 8K 32LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction AVR® UC3 Introduction 標準包裝:2,500 系列:AVR®32 UC3 B 核心處理器:AVR 芯體尺寸:32-位 速度:60MHz 連通性:I²C，IrDA，SPI，SSC，UART/USART，USB 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:28 程序存儲器容量:128KB（128K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:32K x 8 電壓 - 電源 (Vcc/Vdd):1.65 V ~ 1.95 V 數據轉換器:A/D 6x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 包裝:帶卷 (TR) 配用:ATSTK600-TQFP48-ND - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATEVK1101-ND - KIT DEV/EVAL FOR AVR32 AT32UC3B 其它名稱:AT32UC3B1128-AUR-NDAT32UC3B1128-AURTR |
發布緊急采購，3分鐘左右您將得到回復。