參數資料
型號: M37540M4
廠商: Mitsubishi Electric Corporation
英文描述: CABLE ASSEMBLY; 7/16" MALE TO 7/16" MALE; 50 OHM, RG218/U COAX; 48" CABLE LENGTH
中文描述: 單芯片8位CMOS微機
文件頁數: 8/64頁
文件大小: 668K
代理商: M37540M4
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7540 Group
MITSUBISHI MICROCOMPUTERS
8
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
FUNCTIONAL DESCRIPTION
Central Processing Unit (CPU)
The 7540 Group uses the standard 740 family instruction set. Refer
to the table of 740 family addressing modes and machine-language
instructions or the 740 Family Software MANUAL for details on each
instruction set.
Machine-resident 740 family instructions are as follows:
1. The FST and SLW instructions cannot be used.
2. The MUL and DIV instructions can be used.
3. The WIT instruction can be used.
4. The STP instruction can be used.
(This instruction cannot be used while CPU operates by a ring oscil-
lator.)
[CPU mode register] CPUM
The CPU mode register contains the stack page selection bit.
This register is allocated at address 003B
16
.
Switching method of CPU mode register
Switch the CPU mode register (CPUM) at the head of program after
releasing Reset in the following method.
Fig. 9 Switching method of CPU mode register
Fig. 8 Structure of CPU mode register
Oscillation mode selection bit (Note 1)
0 : Ceramic oscillation
CPU mode register
(CPUM: address 003B
16
)
Stack page selection bit
0 : 0 page
Clock division ratio selection bits
b7 b6
φ
) = f(X
IN
)/2 (High-speed mode)
0 1 : f(
φ
) = f(X
IN
)/8 (Middle-speed mode)
1 0 : applied from ring oscillator
φ
) = f(X
IN
) (Double-speed mode)(Note 2)
Ring oscillator oscillation control bit
X
IN
oscillation control bit
0 : Ceramic or RC oscillation enabled
Processor mode bits (Note 1)
0 0 Single-chip mode
0 1
1 0
Not available
b7 b0
2:
These bits are used only when a ceramic oscillation is selected.
Do not use these when an RC oscillation is selected.
Note 1:
The bit can be rewritten only once after releasing reset. After rewriting
it is disable to write any data to the bit. However, by reset the bit is
initialized and can be rewritten, again.
(It is not disable to write any data to the bit for emulator MCU
“M37540RSS”.)
After releasing reset
Switch the oscillation mode
selection bit (bit 5 of CPUM)
Switch the clock division ratio
selection bits (bits 6 and 7 of CPUM)
Main routine
Start with a built-in ring oscillator
An initial value is set as a ceramic
oscillation mode. When it is switched to an
RC oscillation, its oscillation starts.
Switch to other mode except a ring oscillator.
At the same time, select the double-speed,
high-speed, or middle-speed mode.
Wait by ring oscillator operation until
establishment of oscillator clock
When using a ceramic oscillation, wait until
establlishment of oscillation from oscillation starts.
When using an RC oscillation, wait time is not
required basically (time to execute the instruction to
switch from a ring oscillator meets the requirement).
相關PDF資料
PDF描述
M37540M4-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37540M4-XXXGP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37540M4T-XXXGP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37540RSS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37540 Single Chip 8 Bits CMOS Microcomputer(8位單片機)
相關代理商/技術參數
參數描述
M37540M4T-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES
M37540M4T-XXXGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37540M4V-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES
M37540M4V-XXXGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES
M37540M4-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES