- 您現在的位置：買賣IC網 > PDF目錄45034 > M37540E8T-XXXGP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36 PDF資料下載
參數資料
| 型號： | M37540E8T-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36 |
| 封裝： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-36 |
| 文件頁數： | 21/90頁 |
| 文件大小： | 830K |
| 代理商： | M37540E8T-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
7540 Group
Rev.4.00
Jun 21, 2004
page 26 of 82
REJ03B0011-0400Z
qTimer Y
Timer Y is an 8-bit timer and counts the prescaler Y output.
When Timer Y underflows, the timer Y interrupt request bit is set to
“1”.
Prescaler Y is an 8-bit prescaler and counts the signal selected by
the timer Y count source selection bit.
Prescaler Y has the prescaler Y latch to retain the reload value.
Timer Y has the timer Y primary latch and timer Y secondary latch
to retain the reload value.
The value of prescaler Y latch is set to Prescaler Y when
Prescaler Y underflows.The value of timer Y primary latch or timer
Y secondary latch are set to Timer Y when Timer Y underflows.
As for the value to transfer to Timer Y, either of timer Y primary or
timer Y secondary is selected depending on the timer Y operating
mode.
When writing to Prescaler Y (PREY), timer Y primary (TYP) or
timer Y secondary (TYS) is executed, writing to “l(fā)atch only” or
“l(fā)atch and prescaler (timer)” can be selected by the setting value
of the timer Y write control bit. Be sure to set the timer Y write con-
trol bit because there are some notes according to the operating
mode.
When reading from Prescaler Y (PREY) is executed, the count
value of Prescaler Y is read out. When reading from timer Y pri-
mary (TYP) is executed, the count value of Timer Y is read out.
The count value of Timer Y can be read out by reading from the
timer Y primary (TYP) even when the value of timer Y primary
latch or timer Y secondary latch is counted. When reading the
timer Y secondary (TYS) is executed, the undefined value is read
out.
Timer Y can be selected in one of 2 operating modes by setting
the timer Y operating mode bits of the timer Y, Z mode register.
(1) Timer mode
Prescaler Y counts the count source selected by the timer Y count
source selection bits. Each time the count clock is input, the con-
tents of Prescaler Y is decremented by 1. When the contents of
Prescaler Y reach “0016”, an underflow occurs at the next count
clock, and the prescaler Y latch is reloaded into Prescaler Y. The
division ratio of Prescaler Y is 1/(n+1) provided that the value of
Prescaler Y is n.
The contents of Timer Y is decremented by 1 each time the under-
flow signal of Prescaler Y is input. When the contents of Timer Y
reach “0016”, an underflow occurs at the next count clock, and the
timer Y primary latch is reloaded into Timer Y and count continues.
(In the timer mode, the contents of timer Y primary latch is
counted. Timer Y secondary latch is not used in this mode.)
The division ratio of Timer Y is 1/(m+1) provided that the value of
Timer Y is m. Accordingly, the division ratio of Prescaler Y and
Timer Y is 1/((n+1)(m+1)) provided that the value of Prescaler Y
is n and the value of Timer Y is m.
In the timer mode, writing to “l(fā)atch only” or “l(fā)atches and Prescaler
Y and timer Y primary” can be selected by the setting value of the
timer Y write control bit.
(2) Programmable waveform generation mode
In the programmable waveform generation mode, timer counts the
setting value of timer Y primary and the setting value of timer Y
secondary alternately, the waveform inverted each time Timer Y
underflows is output from TYOUT pin.
When using this mode, be sure to set “1” to the timer Y write con-
trol bit to select “write to latch only”. Also, set the port P01 direction
registers to output mode.
The active edge of output waveform is set by the timer Y output
level latch (b5) of the timer Y, Z waveform output control register
(PUM). When “0” is set to b5 of PUM, “H” interval by the setting
value of TYP or “L” interval by the setting value of TYS is output
alternately. When “1” is set to b5 of PUM, “L” interval by the setting
value of TYP or “H” interval by the setting value of TYS is output
alternately.
Also, in this mode, the primary interval and the secondary interval
of the output waveform can be extended respectively for 0.5 cycle
of timer count source clock by setting the timer Y primary wave-
form extension control bit (b2) and the timer Y secondary
waveform extension control bit (b3) of PUM to “1”. As a result, the
waveforms of more accurate resolution can be output.
When b2 and b3 of PUM are used, the frequency and duty of the
output waveform are as follows;
Waveform frequency:
FYOUT=
Duty:
DYOUT=
TMYCL: Timer Y count source (frequency)
TYP: Timer Y primary (8bit)
TYS: Timer Y secondary (8bit)
EXPYP: Timer Y primary waveform extension control bit (1bit)
EXPYS: Timer Y secondary waveform extension control bit (1bit)
In the programmable waveform generation mode, when values of
the TYP, TYS, EXPYP and EXPYS are changed, the output wave-
form is changed at the beginning (timer Y primary waveform
interval) of waveform period.
When the count values are changed, set values to the TYS,
EXPYP and EXPYS first. After then, set the value to TYP. The val-
ues are set all at once at the beginning of the next waveform
period when the value is set to TYP. (When writing at timer stop is
executed, writing to TYP at last is required.)
Notes on programmable waveform generation mode is described
below;
2TMYCL
2(TYP+1)+2(TYS+1)+(EXPYP+EXPYS)
2(TYP+1)+EXPYP
(2(TYP+1)+EXPYP)+(2(TYS+1)+EXPYS)
相關PDF資料 |
PDF描述 |
|---|---|
| M37540M4V-XXXFP | 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| M37540E8V-XXXFP | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| M37540E2FP | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| M37540E2SP | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDIP32 |
| M37540M2T-XXXGP | 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37540E8V-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540E8V-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES |
| M37540EXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540M2T-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540M2T-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES |
發布緊急采購，3分鐘左右您將得到回復。