- 您現在的位置：買賣IC網 > PDF目錄45031 > M37281MKH-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP52 PDF資料下載
參數資料
| 型號： | M37281MKH-XXXSP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP52 |
| 封裝： | PLASTIC, SHRINK, DIP-52 |
| 文件頁數： | 23/158頁 |
| 文件大?。?/td> | 1472K |
| 代理商： | M37281MKH-XXXSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
119
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
MITSUBISHI MICROCOMPUTERS
Rev. 1.0
M37281MAH–XXXSP,M37281MFH–XXXSP
M37281MKH–XXXSP,M37281EKSP
8.14 CLOCK GENERATING CIRCUIT
This microcomputer has 2 built-in oscillation circuits. An oscillation
circuit can be formed by connecting a resonator between XIN and
XOUT (XCIN and XCOUT). Use the circuit constants in accordance with
the resonator manufacturer’s recommended values. No external re-
sistor is needed between XIN and XOUT since a feed-back resistor
exists on-chip. However, an external feed-back resistor is needed
between XCIN and XCOUT. When using XCIN-XCOUT as sub-clock,
clear bits 5 and 4 of the clock source control register to “0.” To supply
a clock signal externally, input it to the XIN (XCIN) pin and make the
XOUT (XCOUT) pin open. When not using XCIN clock, connect the
XCIN to VSS and make the XCOUT pin open.
After reset has completed, the internal clock
φ is half the frequency of
XIN. Immediately after poweron, both the XIN and XCIN clock start
oscillating. To set the internal clock
φ to low-speed operation mode,
set bit 7 of the CPU mode register (address 00FB16) to “1.”
8.14.1 OSCILLATION CONTROL
(1) Stop Mode
When the STP instruction is executed, the internal clock
φ stops at
HIGH. At the same time, timers 3 and 4 are connected by hardware
and “FF16” is set in timer 3 and “0716” is set in timer 4. Select f(XIN)/
16 or f(XCIN)/16 as the timer 3 count source (set both bit 0 of the
timer mode register 2 and bit 6 at address 00C716 to “0” before the
execution of the STP instruction). Moreover, set the timer 3 and timer
4 interrupt enable bits to disabled (“0”) before execution of the STP
instruction. The oscillator restarts when external interrupt is accepted.
However, the internal clock
φ keeps its HIGH level until timer 4 over-
flows, allowing time for oscillation stabilization when a ceramic reso-
nator or a quartz-crystal oscillator is used.
(2) Wait Mode
When the WIT instruction is executed, the internal clock
φ stops in
the HIGH level but the oscillator continues running. This wait state is
released at reset or when an interrupt is accepted (Note). Since the
oscillator does not stop, the next instruction can be executed at once.
Note: In the wait mode, the following interrupts are invalid.
VSYNC interrupt
OSD interrupt
All timers interrupts using external clock from port pin input as count
source
All timer interrupts using f(XIN)/2 or f(XCIN)/2 as count source
All timer interrupts using f(XIN)/4096 or f(XCIN)/4096 as count source
f(XIN)/4096 interrupt
Multi-master I2C-BUS interface interrupt
Data slicer interrupt
A-D conversion interrupt
SPRITE OSD interrupt
Fig.8.14.1 Ceramic Resonator Circuit Example
Fig.8.14.2 External Clock Input Circuit Example
(3) Low-speed Mode
If the internal clock is generated from the sub-clock (XCIN), a low
power consumption operation can be realized by stopping only the
main clock XIN. To stop the main clock, set bit 6 (CM6) of the CPU
mode register (00FB16) to “1.” When the main clock XIN is restarted,
the program must allow enough time to for oscillation to stabilize.
Note that in low-power-consumption mode the XCIN-XCOUT drivability
can be reduced, allowing even lower power consumption. To reduce
the XCIN-XCOUT drivability, clear bit 5 (CM5) of the CPU mode regis-
ter (00FB16) to “0.” At reset, this bit is set to “1” and strong drivability
is selected to help the oscillation to start. When an STP instruction is
executed, set this bit to “1” by software before executing.
XCIN
XIN
CCIN
Microcomputer
XCOUT
Rf
Rd
CCOUT
XOUT
CIN
COUT
XCIN
Microcomputer
External oscillation
circuit or external
pulse
XCOUT XIN
XOUT
Open
External oscillation
circuit
Vcc
Vss
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| M37281MAH-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP52 |
| M37281MFH-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP52 |
| M37410E6HFS | 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQFP80 |
| M37410M3-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
| M37410M4-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M372899234 | 制造商:ITW Switches 功能描述:IN-RUSH |
| M372F3200DJ3-C | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 72 DRAM DIMM with ECC Using 16Mx4, 4K & 8K Refresh, 3.3V |
| M372F3280DJ3-C | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 72 DRAM DIMM with ECC Using 16Mx4, 4K & 8K Refresh, 3.3V |
| M3731 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 SIRENS & MACHINE GUN 2 LEDS BLINKING |
| M3731-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 SIRENS & MACHINE GUN 2 LEDS BLINKING |
發布緊急采購，3分鐘左右您將得到回復。