參數(shù)資料
型號: M37272E8FP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDSO42
封裝: 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42
文件頁數(shù): 125/129頁
文件大?。?/td> 1211K
代理商: M37272E8FP
95
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
M3727GM6/M8–XXXSP/FP
M37272E8SP/FP
MITSUBISHI MICROCOMPUTERS
Rev. 1.0
RESET
Vss
Vcc
Circuit example 1
RESET
Vss
Vcc
Circuit example 2
Note : Make the level change from “L” to “H” at the point at
which the power source voltage exceeds the specified
voltage.
8.15 DISPLAY OSCILLATION CIRCUIT
The OSD oscillation circuit has a built-in clock oscillation circuits, so
that a clock for OSD can be obtained simply by connecting an LC, a
ceramic resonator, or a quartz-crystal oscillator across the pins OSC1
and OSC2. Which of the sub-clock or the OSD oscillation circuit is
selected by setting bits 5 and 6 of the OSD control register (address
00D016).
8.17 ADDRESSING MODE
The memory access is reinforced with 17 kinds of addressing modes.
Refer to SERIES 740 <Software> User’s Manual for details.
8.18 MACHINE INSTRUCTIONS
There are 71 machine instructions. Refer to SERIES 740 <Soft- ware>
User’s Manual for details.
9. PROGRAMMING NOTES
The divide ratio of the timer is 1/(n+1).
Even though the BBC and BBS instructions are executed imme-
diately after the interrupt request bits are modified (by the pro-
gram), those instructions are only valid for the contents before
the modification. At least one instruction cycle is needed (such as
an NOP) between the modification of the interrupt request bits
and the execution of the BBC and BBS instructions.
After the ADC and SBC instructions are executed (in the decimal
mode), one instruction cycle (such as an NOP) is needed before
the SEC, CLC, or CLD instruction is executed.
An NOP instruction is needed immediately after the execution of
a PLP instruction.
In order to avoid noise and latch-up, connect a bypass capacitor
(
≈ 0.1F) directly between the VCC pin–VSS pin, AVCC pin–VSS
pin, and the VCC pin–CNVSS pin, using a thick wire.
M3727GM6/M8-XXXSP and M37272E8SP/FP are compatible, but
please attention differences as follows:
Fig.8.15.1 Display Oscillation Circuit
8.16 AUTO-CLEAR CIRCUIT
When a power source is supplied, the auto-clear function will oper-
ate by connecting the following circuit to the RESET pin.
Fig.8.16.1 Auto-clear Circuit Example
OSC2
OSC1
L
C1
C2
Parameter
Spec of1 4th pins
M37272E8SP/FP
AVcc
M3727GM6/M8-XXXSP/FP
NC (Non connection)
OSD : OFF
Data slicer : OFF
OSD : ON
Data slicer : ON
Power souce voltage
When System operate
f(XIN) : 8MFz
Normal
15 mA
30mA
Max.
30 mA
45 mA
Normal
10 mA
25 mA
Max.
25 mA
40 mA
Need to apply 5V±10%, because 14th pin of M37272E8SP/FP
is AVcc pin.
M3727GM6/M8-XXXSP/FP is the non connection pin, but it is
not connect to the inside of IC. You can apply voltage.
相關PDF資料
PDF描述
M3727GM8-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42
M37272E8SP 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDIP42
M3727GM6-XXXFP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42
M37272M6-XXXFP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42
M37272M6-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42
相關代理商/技術參數(shù)
參數(shù)描述
M37272E8SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37272EF8FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37272EF8SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37272EFFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37272EFSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER