- 您現在的位置：買賣IC網 > PDF目錄98005 > M37224M3-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 PDF資料下載
參數資料
| 型號： | M37224M3-XXXSP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| 封裝： | 0.600 INCH, 1.778 MM PITCH, SHRINK, PLASTIC, DIP-42 |
| 文件頁數： | 15/83頁 |
| 文件大?。?/td> | 901K |
| 代理商： | M37224M3-XXXSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁
M37224M3-XXXSP
MITSUBISHI MICROCOMPUTERS
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
22
Fig. 19. Serial I/O Timing (for LSB first)
Synchronous clock
Transfer clock
Serial I/O register
write signal
Serial I/O output
SOUT
D0
D1
D2
D3
D4
D5
D6
D7
(Note)
Serial I/O input
SIN
Note : When an internal clock is selected, the S OUT pin is at high-impedance after transfer is completed.
Interrupt request bit is set to “1”
Internal clock: The serial I/O counter is set to “7” during the write
cycle into the serial I/O register (address 00DD16), and the transfer
clock goes “H” forcibly. At each falling edge of the transfer clock after
the write cycle, serial data is output from the SOUT pin. Transfer di-
rection can be selected by bit 5 of the serial I/O mode register. At
each rising edge of the transfer clock, data is input from the SIN pin
and data in the serial I/O register is shifted 1 bit.
After the transfer clock has counted 8 times, the serial I/O counter
becomes “0” and the transfer clock stops at HIGH. At this time the
interrupt request bit is set to “1.”
External clock: When an external clock is selected as the clock source,
the interrupt request is set to “1” after the transfer clock has been
counted 8 counts. However, transfer operation does not stop, so the
clock should be controlled externally. Use the external clock of 1MHz
or less with a duty cycle of 50%.
The serial I/O timing is shown in Figure 19. When using an external
clock for transfer, the external clock must be held at HIGH for initial-
izing the serial I/O counter. When switching between an internal clock
and an external clock, do not switch during transfer. Also, be sure to
initialize the serial I/O counter after switching.
Notes 1: On programming, note that the serial I/O counter is set by
writing to the serial I/O register with the bit managing in-
structions, such as SEB and CLB.
2: When an external clock is used as the synchronous clock,
write transmit data to the serial I/O register when the trans-
fer clock input level is HIGH.
相關PDF資料 |
PDF描述 |
|---|---|
| M37270MF-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP64 |
| M37273MFH-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP52 |
| M3727GM8-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42 |
| M37280MFH-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64 |
| M37280MKH-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37225ECSP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37225M6 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37225M8 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37225MA | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M372429100 | 制造商:ITW Switches 功能描述:IN-RUSH |
發布緊急采購，3分鐘左右您將得到回復。