MITSUBISHI MICROCOMPUTERS
M37221M6-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
24
Fig. 21. START condition/STOP condition detecting timing diagram
Table 5. START condition/STOP condition detecting conditions
(8) START/STOP Condition Detecting Condi-
tions
The START/STOP condition detecting conditions are shown in Fig-
ure 21 and Table 5. Only when the 3 conditions of Table 5 are satis-
fied, a START/STOP condition can be detected.
Note: When a STOP condition is detected in the slave mode
(MST = 0), an interrupt request signal “IICIRQ” occurs to the
CPU.
Standard clock mode
6.5
s (26 cycles) < SCL release
time
3.25
s (13 cycles) < Setup time
3.25
s (13 cycles) < Hold time
High-speed clock mode
1.0
s (4 cycles) < SCL release
time
0.5
s (2 cycles) < Setup time
0.5
s (2 cycles) < Hold time
Note: Absolute time at
φ = 4 MHz. The value in parentheses de-
notes the number of
φ cycles.
(9) Address Data Communication
There are two address data communication formats, namely, 7-bit
addressing format and 10-bit addressing format. The respective ad-
dress communication formats is described below.
7-bit addressing format
To meet the 7-bit addressing format, set the 10BIT SAD bit of the
I2C control register (address 00DA16) to “0.” The first 7-bit address
data transmitted from the master is compared with the high-order
7-bit slave address stored in the I2C address register (address
00D816). At the time of this comparison, address comparison of
the RBW bit of the I2C address register (address 00D816) is not
made. For the data transmission format when the 7-bit addressing
format is selected, refer to Figure 22, (1) and (2).
10-bit addressing format
To meet the 10-bit addressing format, set the 10BIT SAD bit of the
I2C control register (address 00DA16) to “1.” An address compari-
son is made between the first-byte address data transmitted from
the master and the 7-bit slave address stored in the I2C address
register (address 00D816). At the time of this comparison, an ad-
dress comparison between the RBW bit of the I2C address regis-
ter (address 00D816) and the R/W bit which is the last bit of the
address data transmitted from the master is made. In the 10-bit
addressing mode, the R/W bit which is the last bit of the address
data not only specifies the direction of communication for control
data but also is processed as an address data bit.
Fig. 22. Address data communication format
Hold time
Setup
time
SCL
SDA
(START condition)
SDA
(STOP condition)
SCL release time
Hold time
Setup
time
S
Slave address
A
Data
A
Data
A/A
P
R/W
7 bits
“0”
1 to 8 bits
S
Slave address
A
Data
A
Data
AP
7 bits
“1”
1 to 8 bits
(1) A master-transmitter transmits data to a slave-receiver
S
Slave address
1st 7 bits
A
Data
7 bits
“0”
8 bits
1 to 8 bits
(2) A master-receiver receives data from a slave-transmitter
Slave address
2nd byte
A
Data
A/A
P
1 to 8 bits
S
Slave address
1st 7 bits
A
7 bits
“0”
8 bits
7 bits
(3) A master-transmitter transmits data to a slave-receiver with a 10-bit address
Slave address
2nd byte
Data
1 to 8 bits
Sr
Slave address
1st 7 bits
A
Data
AP
1 to 8 bits
“1”
(4) A master-receiver receives data from a slave-transmitter with a 10-bit address
S : START condition
P : STOP condition
A : ACK bit
R/W : Read/Write bit
Sr : Restart condition
From master to slave
From slave to master
R/W