- 您現在的位置：買賣IC網 > PDF目錄45029 > M35076-XXXSP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 PDF資料下載
參數資料
| 型號： | M35076-XXXSP |
| 元件分類： | 顯示控制器 |
| 英文描述： | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
| 封裝： | 0.300 INCH, 1.78 MM PITCH, PLASTIC, SDIP-20 |
| 文件頁數： | 30/48頁 |
| 文件大?。?/td> | 477K |
| 代理商： | M35076-XXXSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
MITSUBISHI MICROCOMPUTERS
M35076-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
33
NOTE FOR SUPPLYING POWER
__
(1)Timing of power supplying to AC pin
The internal circuit of M35076-XXXSP is reset when the level of
__
the auto clear input pin AC is “L”. This pin in hysteresis input with
the pull-up resistor.
__
The timing about power supplying of AC pin is shown in Figure 19.
PRECAUTION FOR USE
Notes on noise and latch-up
In order to avoid noise and latch-up, connect a bypass capacitor
(
≈0.1F) directly between the VDD1 pin and VSS1 pin, and the VDD2
pin and VSS2 pin using a heavy wire.
Fig. 19
__
Timing of power supplying to AC pin
After supplying the power (VDD and VSS) to M35076-XXXSP and
the supply voltage becomes more than 0.8
× VDD, it needs to keep
__
VIL time; tw of the AC pin for more than 1ms.
__
Start inputting from microcomputer after AC pin supply voltage
becomes more than 0.8
× VDD and keeping 200ms wait time.
(2)Timing of power supplying to VDD1 and VDD2.
Supply power to VDD1 and VDD2 at the same time.
Note for waveform timing of the horizontal signals to the HOR pin
Set horizontal synchronous signal edge waveform timing to under
5ns and input to HOR pin.
_
Set only the side which set by B/F register waveform timing under
5ns and input to HOR pin.
_
: Set front porch edge or back porch edge by B/F register.
Voltage [V]
VDD
0.8 x VDD
0.2 x VDD
Supply voltage
more than 1ms
tW
tS
Time t [s]
Data input disable
VAC
(AC pin input voltage)
90%
10%
tf
tr
Horizontal synchronous signal
DATA REQUIRED FOR MASK ROM
ORDERING
Please send the following data for mask orders.
(1) M35076-XXXSP mask ROM order confirmation form
(2) 20P4B mark specification form
(3) ROM data : EPROMs or floppy disks
*In the case of EPROMs, thres sets of EPROMs are required
per pattern.
*In the case of floppy disks, 3.5-inch 2HD disk (1BM format) is
required per pattern.
相關PDF資料 |
PDF描述 |
|---|---|
| M35080FP | 128 X 96 DOTS CRT CHAR OR GRPH DSPL CTLR, PDSO24 |
| M37102E8-XXXFP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| M37102E8-XXXSP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP64 |
| M37102M8-XXXSP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP64 |
| M37201E6-XXXSP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M35080 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080BN | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080-BN3T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080-BN6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。