- 您現在的位置：買賣IC網 > PDF目錄45010 > M30221MC-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | M30221MC-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP120 |
| 封裝： | PLASTIC, LQFP-120 |
| 文件頁數： | 18/45頁 |
| 文件大?。?/td> | 346K |
| 代理商： | M30221MC-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
25
Usage precaution
Mitsubishi microcomputers
M30221 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Stop Mode and Wait Mode
A-D Converter
(1) If changing the measurement mode select bit is set after a count is started, the timer Bi interrupt
request bit goes to “1”.
(2) When the first effective edge is input after a count is started, an indeterminate value is transferred to
the reload register. At this time, timer Bi interrupt request is not generated.
Timer B (pulse period/pulse width measurement mode)
(1) Write to each bit (except bit 6) of A-D control register 0, to each bit of A-D control register 1, and to bit
0 of A-D control register 2 when A-D conversion is stopped (before a trigger occurs).
In particular, when the Vref connection bit is changed from “0” to “1”, start A-D conversion after an
elapse of 1
s or longer.
(2) When changing A-D operation mode, select analog input pin again.
(3) Using one-shot mode or single sweep mode
Read the correspondence A-D register after confirming A-D conversion is finished. (It is known by A-
D conversion interrupt request bit.)
(4) Using repeat mode, repeat sweep mode 0 or repeat sweep mode 1
Use the undivided main clock as the internal CPU clock.
____________
(1) When returning from stop mode by hardware reset, RESET pin must be set to “L” level until main clock
oscillation is stabilized.
(2) When switching to either wait mode or stop mode, instructions occupying four bytes either from the
WAIT instruction or from the instruction that sets the every-clock stop bit to “1” within the instruction
queue are prefetched and then the program stops. So put at least four NOPs in succession either to
the WAIT instruction or to the instruction that sets the every-clock stop bit to “1”.
(3) When the MCU running in low-speed or low power dissipation mode, do not enter WAIT mode with
peripheral function clock stop bit (CM02) set to "1".
(1) Make sure timer Ai for real time port output is set for timer mode, and is set to have “no gate function”
using the gate function select bit.
(2) Before setting the real time port mode select bit to “1”, temporarily turn off the timer Ai used and write
its set value to the timer Ai register.
Real time port
(1) In case IIC mode select bit (bit 0 of address 037716) is set to "1" with UART2.When setting up port
direction P7 (address 03EF16), write immediate values. If you use Read/Modify/Write instructions
(BSET,BCLR,AND,OR,etc..) on the P7 direction register, the value of P71 direction register may
change to unknown data.
(2) MASK ROM version ONRY when IIC mode select bit (bit 0 of address 037716) and the internal/
external select bit (bit 3 of address 037816) are both set to "1". The function of "SCL wait output bit 2
(bit 5 of address 037616)" dose not work.
(3) MASK ROM version ONRY when IIC mode select bit (bit 0 of address 037716) and the internal/
external select bit (bit 3 of address 037816) are both set to "1". According to the datasheet, when IICM
is set to "1", the port terminal is readable by the CPU even though "1" is assigned to P71 of the
direction register. However, the CPU cannot read port P71 data if the P71 direction register is set to
"1".
Sirial I/O
相關PDF資料 |
PDF描述 |
|---|---|
| M30240MC-XXXFP | 16-BIT, MROM, MICROCONTROLLER, PQFP80 |
| M30240M4-XXXFP | 16-BIT, MROM, MICROCONTROLLER, PQFP80 |
| M30240M1-XXXFP | 16-BIT, MROM, MICROCONTROLLER, PQFP80 |
| M30245MC-XXXGP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| M30245FCGP | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30222 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30222FG | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30222FGFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30222FGGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30222FG-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。