參數資料
型號: M30201M2-XXXSP
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
中文描述: 單片16位CMOS微機
文件頁數: 128/159頁
文件大?。?/td> 1496K
代理商: M30201M2-XXXSP
Unde
CPU Rewrite Mode
Peimnay
deeopmen
Mitsubishi microcomputers
M30201 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
128
Microcomputer Mode and Boot Mode
The control program for CPU rewrite mode must be written into the user ROM or boot ROM area in
parallel I/O mode beforehand. (If the control program is written into the boot ROM area, the standard
serial I/O mode becomes unusable.)
See Figure AA-3 for details about the boot ROM area.
Normal microcomputer mode is entered when the microcomputer is reset with pulling CNV
SS
pin low
(V
SS
). In this case, the CPU starts operating using the control program in the user ROM area.
When the microcomputer is reset by pulling the P5
2
pin high (V
CC
), the CNV
SS
pin high(V
PPH
), the CPU
starts operating using the control program in the boot ROM area. This mode is called the “boot” mode.
The control program in the boot ROM area can also be used to rewrite the user ROM area.
CPU rewrite mode operation procedure
The internal flash memory can be operated on to program, read, verify, or erase it while being placed on-
board by writing commands from the CPU to the flash memory control register (addresses 03B4
16
,
03B5
16
) and flash command register (address 03B6
16
). Note that when in CPU rewrite mode, the boot
ROM area cannot be accessed for program, read, verify, or erase operations. Before this can be accom-
plished, a CPU write control program must be written into the boot ROM area in parallel input/output
mode. The following shows a CPU rewrite mode operation procedure.
<Start procedure (Note 1)>
(1) Apply V
PP
H to the CNV
SS
/V
PP
pin and V
CC
to the port P5
2
pin for reset release. Or the user can
jump from the user ROM area to the boot ROM area using the JMP instruction and execute the CPU
write control program. In this case, set the CPU write mode select bit of the flash memory control
register to “1” before applying V
PP
H to the CNV
SS
/V
PP
pin.
(2) After transferring the CPU write control program from the boot ROM area to the internal RAM, jump
to this control program in RAM. (The operations described below are controlled by this program.)
(3) Set the CPU rewrite mode select bit to “1”.
(4) Read the CPU rewrite mode monitor flag to see that the CPU rewrite mode is enabled.
(5) Execute operation on the flash memory by writing software commands to the flash command regis-
ter.
Note 1: In addition to the above, various other operations need to be performed, such as for entering the
data to be written to flash memory from an external source (e.g., serial I/O), initializing the ports, and
writing to the watchdog timer.
<Clearing procedure>
(1) Apply V
SS
to the CNV
SS
/V
PP
pin.
相關PDF資料
PDF描述
M30201M4T-XXXFP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201M4T-XXXSP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201M4-XXXSP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201M6T-XXXFP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201M6T-XXXSP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M30201M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201M4-114FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201M4T 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201M4T-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY
M30201M4T-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY