- 您現在的位置：買賣IC網 > PDF目錄358999 > M27V401-200K6TR (意法半導體) Quadruple 2-Input Positive-NAND Gates 14-SOIC 0 to 70 PDF資料下載
參數資料
| 型號： | M27V401-200K6TR |
| 廠商： | 意法半導體 |
| 英文描述： | Quadruple 2-Input Positive-NAND Gates 14-SOIC 0 to 70 |
| 中文描述： | 4兆位512KB的x8低壓紫外線EPROM和檢察官辦公室存儲器 |
| 文件頁數： | 9/15頁 |
| 文件大?。?/td> | 103K |
| 代理商： | M27V401-200K6TR |
9/15
M27V401
On-Board Programming
The M27V401 can be directly programmed in the
application circuit. See the relevant Application
Note AN620.
Electronic Signature
The Electronic Signature (ES) mode allows the
reading out of a binary code from an EPROM that
will identify its manufacturer and type. This mode
is intended for use by programming equipment to
automatically matchthe device to be programmed
with its corresponding programming algorithm.
The ES mode is functional in the 25
°
C
±
5
°
C am-
bient temperaturerange that is required when pro-
gramming theM27V401. To activatethe ES mode,
the programming equipment must force 11.5V to
12.5V on address line A9 of the M27V401, with
V
PP
= V
CC
= 5V. Two identifier bytes may then be
sequenced fromthe device outputs by toggling ad-
dress line A0 from V
IL
to V
IH
. All other address
lines must be held at V
IL
during Electronic Signa-
ture mode.
Byte 0 (A0=V
IL
) represents themanufacturer code
and byte 1 (A0=V
IH
) the device identifier code. For
the STMicroelectronics M27V401, these two iden-
tifier bytes are given in Table 4 and can be read-
out on outputs Q0 to Q7. Note that the M27V401
and M27C4001 have the same identifier bytes.
ERASURE OPERATION (applies to UV EPROM)
The erasure characteristics of the M27V401 is
such that erasure begins when the cells are ex-
posed to light with wavelengths shorter than ap-
proximately 4000. Itshould benoted that sunlight
and some type of fluorescent lamps have wave-
lengths in the 3000-4000 range. Research
shows that constant exposure to room level fluo-
rescent lighting could erase a typical M27V401 in
about 3 years, while it would takeapproximately 1
week to cause erasure when exposed to direct
sunlight. If the M27V401 is to be exposed to these
types of lighting conditions for extended periods of
time, it is suggested that opaque labelsbeput over
the M27V401 window to prevent unintentional era-
sure. The recommended erasure procedure for
the M27V401 is exposure to short wave ultraviolet
light which has a wavelength of 2537. The inte-
grated dose (i.e. UV intensity x exposure time) for
erasure should be a minimum of 15 W-sec/cm
2
.
The erasure time with this dosage is approximate-
ly 15 to 20 minutes using an ultraviolet lamp with
12000
μ
W/cm
2
power rating. The M27V401
should be placed within 2.5 cm (1inch) of the lamp
tubes during the erasure. Somelamps have a filter
on their tubes which should be removed before
erasure.
相關PDF資料 |
PDF描述 |
|---|---|
| M27V401-200N6TR | 4 Mbit 512Kb x8 Low Voltage UV EPROM and OTP EPROM |
| M27V401-180K1TR | 4 Mbit 512Kb x8 Low Voltage UV EPROM and OTP EPROM |
| M27V402-120B4TR | 4 Mbit 256Kb x 16 Low Voltage UV EPROM and OTP EPROM |
| M27V402-150B4TR | 4 Mbit 256Kb x 16 Low Voltage UV EPROM and OTP EPROM |
| M27V402-200B4TR | 4 Mbit 256Kb x 16 Low Voltage UV EPROM and OTP EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M27V401-200N1TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8 Low Voltage UV EPROM and OTP EPROM |
| M27V401-200N6TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8 Low Voltage UV EPROM and OTP EPROM |
| M27V402 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 256Kb x 16 Low Voltage UV EPROM and OTP EPROM |
| M27V402-120B1TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 256Kb x 16 Low Voltage UV EPROM and OTP EPROM |
| M27V402-120B4TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 256Kb x 16 Low Voltage UV EPROM and OTP EPROM |
發布緊急采購，3分鐘左右您將得到回復。