- 您現在的位置：買賣IC網 > PDF目錄299427 > M24C02-RDW6G (STMICROELECTRONICS) 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | M24C02-RDW6G |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封裝： | 0.169 INCH, ROHS COMPLIANT, TSSOP-8 |
| 文件頁數： | 5/37頁 |
| 文件大?。?/td> | 322K |
| 代理商： | M24C02-RDW6G |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
M24C16, M24C08, M24C04, M24C02, M24C01
Device operation
3.5
Memory addressing
To start communication between the bus master and the slave device, the bus master must
initiate a Start condition. Following this, the bus master sends the device select code, shown
in Table 3 (on Serial Data (SDA), most significant bit first).
The device select code consists of a 4-bit Device Type Identifier, and a 3-bit Chip Enable
“Address” (E2, E1, E0). To address the memory array, the 4-bit Device Type Identifier is
1010b.
Each device is given a unique 3-bit code on the Chip Enable (E0, E1, E2) inputs. When the
device select code is received, the device only responds if the Chip Enable Address is the
same as the value on the Chip Enable (E0, E1, E2) inputs. However, those devices with
larger memory capacities (the M24C16, M24C08 and M24C04) need more address bits. E0
is not available for use on devices that need to use address line A8; E1 is not available for
devices that need to use address line A9, and E2 is not available for devices that need to
up to eight M24C02 (or M24C01), four M24C04, two M24C08 or one M24C16 devices can
be connected to one IC bus. In each case, and in the hybrid cases, this gives a total
memory capacity of 16 Kbits, 2 KBytes (except where M24C01 devices are used).
The 8th bit is the Read/Write bit (RW). This bit is set to 1 for Read and 0 for Write operations.
If a match occurs on the device select code, the corresponding device gives an
acknowledgment on Serial Data (SDA) during the 9th bit time. If the device does not match
the device select code, it deselects itself from the bus, and goes into Standby mode.
Table 4.
Operating modes
Mode
RW bit
WC(1)
1.
X = VIH or VIL.
Bytes
Initial sequence
Current Address Read
1
X
1
Start, Device Select, RW = 1
Random Address Read
0X
1
Start, Device Select, RW = 0, Address
1
X
reStart, Device Select, RW = 1
Sequential Read
1
X
≥ 1
Similar to Current or Random Address
Read
Byte Write
0
VIL
1
Start, Device Select, RW = 0
Page Write
0
VIL
≤16
Start, Device Select, RW = 0
相關PDF資料 |
PDF描述 |
|---|---|
| M24C08-RDS6TP | 1K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| M24C16-RDW6G | 2K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| M278-S20-201-2 | 20 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER, SOCKET |
| M278-S20-201-3 | 20 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER, SOCKET |
| M278-S20-201-4 | 20 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER, SOCKET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M24C02-RDW6T | 功能描述:電可擦除可編程只讀存儲器 5.5V 2K (256x8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M24C02-RDW6TP | 功能描述:電可擦除可編程只讀存儲器 E-EPROM RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M24C02-RDW6TP PBF | 制造商:STMicroelectronics 功能描述: |
| M24C02-RMB6TG | 功能描述:電可擦除可編程只讀存儲器 16 Kbit 8 Kbit 4 Kbit 2 Kbit RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M24C02-RMC6TG | 功能描述:電可擦除可編程只讀存儲器 2Kbit 100kHz I2C 400 kHZ Fast-Mode RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。