- 您現在的位置：買賣IC網 > PDF目錄45009 > M0710LC600 (WESTCODE SEMICONDUCTORS LTD) 710 A, 6000 V, SILICON, RECTIFIER DIODE PDF資料下載
參數資料
| 型號： | M0710LC600 |
| 廠商： | WESTCODE SEMICONDUCTORS LTD |
| 元件分類： | 整流器 |
| 英文描述： | 710 A, 6000 V, SILICON, RECTIFIER DIODE |
| 文件頁數： | 6/11頁 |
| 文件大?。?/td> | 648K |
| 代理商： | M0710LC600 |
WESTCODE
WESTCODE An IXYS Company
Fast Recovery Diode Types M0710LC560 to M0710LC600
Data Sheet. Types M0710LC560 to M0710LC600 Issue 1
Page 4 of 13
December, 2002
5.0 Reverse Recovery Loss
The following procedure is recommended for use where it is necessary to include reverse recovery loss.
From waveforms of recovery current obtained from a high frequency shunt (see Note 1) and reverse
voltage present during recovery, an instantaneous reverse recovery loss waveform must be constructed.
Let the area under this waveform be E joules per pulse. A new sink temperature can then be evaluated
from:
[]
)
(
)
(
Hs
J
th
MAX
J
SINK
R
f
k
E
T
+
=
Where k = 0.2314 (°C/W)/s
E = Area under reverse loss waveform per pulse in joules (W.s.)
f = Rated frequency in Hz at the original sink temperature.
Rth(J-Hs) = d.c. thermal resistance (°C/W)
The total dissipation is now given by:
f
E
W
original
tot
+
=
)
(
)
(
NOTE 1 - Reverse Recovery Loss by Measurement
This device has a low reverse recovered charge and peak reverse recovery current. When measuring the
charge, care must be taken to ensure that:
(a) AC coupled devices such as current transformers are not affected by prior passage of high
amplitude forward current.
(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope
to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal.
(c) Measurement of reverse recovery waveform should be carried out with an appropriate critically
damped snubber, connected across diode anode to cathode. The formula used for the calculation of this
snubber is shown below:
dt
di
S
r
C
V
R
= 4
2
Where: Vr = Commutating source voltage
CS = Snubber capacitance
R = Snubber resistance
6.0 Snubber Components
When selecting snubber components, care must be taken not to use excessively large values of snubber
capacitor or excessively small values of snubber resistor. Such excessive component values may lead to
device damage due to the large resultant values of snubber discharge current. If required, please consult
the factory for assistance.
相關PDF資料 |
PDF描述 |
|---|---|
| M0955LC200 | 955 A, 2000 V, SILICON, RECTIFIER DIODE |
| M1010NC400 | 1010 A, 4000 V, SILICON, RECTIFIER DIODE |
| M1010NC450 | 1010 A, 4500 V, SILICON, RECTIFIER DIODE |
| M1502NC220 | 1502 A, 2200 V, SILICON, RECTIFIER DIODE |
| M1583VC440 | 1583 A, 4400 V, SILICON, RECTIFIER DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M0711-4-N | 制造商:RAF Electronic Hardware 功能描述:Rnd Metr Spcr 13mm 2mm L X M4 |
| M0711-5-N | 功能描述:支架與墊片 Rnd Metr Spcr 13mm 2mm L X M5 RoHS:否 制造商:Schurter 類型:Transipillar Spacers 長度:16 m 螺紋大小:M4 外徑:10 mm 材料:Nylon with Steel 電鍍:Zinc |
| M0711-6-N | 功能描述:支架與墊片 Rnd Metr Spcr 13mm 2mm L X M6 RoHS:否 制造商:Schurter 類型:Transipillar Spacers 長度:16 m 螺紋大小:M4 外徑:10 mm 材料:Nylon with Steel 電鍍:Zinc |
| M0711-6-S-12 | 制造商:RAF Electronic Hardware 功能描述: |
| M0712-5-N | 功能描述:支架與墊片 Rnd Metr Spcr 13mm 3mm L X M5 RoHS:否 制造商:Schurter 類型:Transipillar Spacers 長度:16 m 螺紋大小:M4 外徑:10 mm 材料:Nylon with Steel 電鍍:Zinc |
發布緊急采購，3分鐘左右您將得到回復。