- 您現在的位置：買賣IC網 > PDF目錄11000 > M-991-01SM (IXYS Integrated Circuits Division)IC TONE GENERATR LP CMOS 16-SOIC PDF資料下載
參數資料
| 型號： | M-991-01SM |
| 廠商： | IXYS Integrated Circuits Division |
| 文件頁數： | 3/5頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TONE GENERATR LP CMOS 16-SOIC |
| 標準包裝： | 46 |
| 功能： | 音頻發生器 |
| 電路數： | 1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
INTEGRATED CIRCUITS DIVISION
M-991
www.ixysic.com
3
R03
Call progress tones are audible tones sent from
switching systems to calling parties (or equipment) to
indicate the status of calls. Calling parties can identify
the success of a placed call by what is heard after
dialing. The M-991 series utilizes a highly linear tone
generator that produces the unique frequencies (singly
or in pairs) that are common to call progress signals.
Duration and frequency selection are digitally
controlled (see the Data/Tone Selection table below for
data settings for a particular tone output). A typical
control sequence for the M-991 is: (1) set data lines to
desired frequency selection, (2) wait for data lines to
settle, (3) drive the chip enable (CE) low, (4) maintain
CE low for desired tone duration (Note: data lines may
be changed after data hold time), and (4) return CE to
a logic high. (Commonly used call progress tones are
Call Progress Tone Generation
shown in the Data/Tone Selection table below.) In a
bus-oriented system, noise on the data lines may
propagate through the device and appear at the
output. To safeguard against this, use an external latch
to lock the data into the device. In addition, it is good
practice to bypass the V
REF pin to ground with a
small capacitor (0.01
F) to reduce power supply
noise. The designer should be aware of device timing
requirements and design accordingly. The data input
pins may be tied high (+5 VDC) or low (ground) as
required, but D4 and D5 must be left open. Beware of
hardwiring the CE pin for dedicated tone generation.
This input is edge triggered. An RC network like that
shown in the Power-on Reset Circuit on Page 4 should
be used to momentarily reset the device immediately
following power-up to ensure proper operation.
D3
D2
D1
D0
Frequency (Hz)
Use
12
0000
300
440
Dial Tone
0001
400
off
Special
0010
440
off
Alert Tone
0011
440
480
Audible Ring
0100
440
620
Pre-empt
0101
480
off
Bell high tone
0110
480
620
Reorder (Bell low)
0111
350
off
Special
1000
620
off
Special
1001
941
1209
DTMF " * "
Tone Name
Frequency (Hz)
1
2
Interruption Rate
Dial
350
440
Steady
Reorder
480
620
Repeat, tones on and off 250 ms ± 25 ms each.
Busy
480
620
Repeat, tones on and off 500 ms ± 50 ms each.
Audible Ring
440
480
Repeat, tones on 2 ± 0.2 s, tones off 4 ± 0.4 s
Recall Dial
350
440
Three bursts tones on and off 100 ms ± 20 ms each followed by dial tone.
Special AR
440
480
Tones on 1 ± 0.2s, followed by single 440 Hz on for 0.2s on, and silence for 3 ± 0.3 s, repeat.
Intercept
440
620
Repeat alternating tones, each on for 230 ms ± 70 ms with total cycle of 500 ± 50 ms.
Call Waiting
440
off
One burst 200 ± 100 ms
Busy Verication
440
off
One burst of tone on 1.75 ± 0.25 s before attendant intrudes, followed by burst of tone 0.65 ± 0.15 s on, 8 to
20 s apart for as long as the call lasts
Executive Override
440
off
One burst of tone for 3 ± 1 s before overriding station intrudes
Conrmation
350
440
Three bursts on and off 100 ms each or 100 ms on, 100 ms off, 300 ms on
Pin
Function
CE
Latches data and enables output (active low input)
D0 - D3
Data input pins (See Data/Tone Selection)
D4 - D5
Leave open
MUTE
Output indicates that a signal is being generated at
OUTDRIVE.
OUTDRIVE Linear buffered tone output.
V
DD
Most positive power supply input pin.
V
REF
Internally generated mid-power supply voltage (output).
V
SS
Most negative power supply input pin.
X
IN
Crystal oscillator or digital clock input.
X
OUT
Crystal oscillator output.
Data/Tone Selection
Pin Function
Standard Call Progress Tones
相關PDF資料 |
PDF描述 |
|---|---|
| LT1684IS#TRPBF | IC RING TONE GENERATOR 14-SOIC |
| VE-BNZ-IX-B1 | CONVERTER MOD DC/DC 2V 30W |
| VE-BNZ-IW-B1 | CONVERTER MOD DC/DC 2V 40W |
| VI-272-IY-F2 | CONVERTER MOD DC/DC 15V 50W |
| LT1684IS#TR | IC GENERATOR RING TONE 14SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M-991-01SMTR | 功能描述:固態繼電器-PCB安裝 5V Call Progress Tone Generator, 16xpin RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| M-991-02SM | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:Call Progress Tone Generator |
| M-991-02SMTR | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:Call Progress Tone Generator |
| M9911 | 制造商:Tamura Corporation of America 功能描述: |
| M9913 | 制造商:Tamura Corporation of America 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。