- 您現在的位置：買賣IC網 > PDF目錄358968 > LZ24BP (Sharp Corporation) 1/4-type Progressive-scan Color CCD Area Sensor with 350 k Pixels PDF資料下載
參數資料
| 型號： | LZ24BP |
| 廠商： | Sharp Corporation |
| 英文描述： | 1/4-type Progressive-scan Color CCD Area Sensor with 350 k Pixels |
| 中文描述： | 1/4-type逐行掃描，350萬像素彩色CCD區域傳感器 |
| 文件頁數： | 10/10頁 |
| 文件大?。?/td> | 87K |
| 代理商： | LZ24BP |
3) To avoid generating static electricity,
a. do not scrub the glass surface with cloth or
plastic.
b. do not attach any tape or labels.
c. do not clean the glass surface with dust-
cleaning tape.
4) When storing or transporting the device, put it in
a container of conductive material.
3. Dust and Contamination
Dust or contamination on the glass surface could
deteriorate the output characteristics or cause a
scar. In order to minimize dust or contamination on
the glass surface, take the following precautions :
1) Handle the CCD in a clean environment such
as a cleaned booth. (The cleanliness level
should be, if possible, class 1 000 at least.)
2) Do not touch the glass surface with the fingers.
If dust or contamination gets on the glass
surface, the following cleaning method is
recommended :
Dust from static electricity should be blown
off with an ionized air blower. For anti-
electrostatic measures, however, ground all
the leads on the device before blowing off
the dust.
The contamination on the glass surface
should be wiped off with a clean applicator
soaked in Isopropyl alcohol. Wipe slowly and
gently in one direction only.
– Frequently replace the applicator and do not
use the same applicator to clean more than
one device.
Note : In most cases, dust and contamination
are unavoidable, even before the device
is first used. It is, therefore, recommended
that the above procedures should be
taken to wipe out dust and contamination
before using the device.
4. Other
1) Soldering should be manually performed within
5 seconds at 350 °C maximum at soldering iron.
2) Avoid using or storing the CCD at high tem-
perature or high humidity as it is a precise
optical component. Do not give a mechanical
shock to the CCD.
3) Do not expose the device to strong light. For
the color device, long exposure to strong light
will fade the color of the color filters.
10
PRECAUTIONS FOR CCD AREA SENSORS
相關PDF資料 |
PDF描述 |
|---|---|
| LZ34B10 | 1/4-type Color CMOS Image Sensor with 350 k Pixels |
| LZ34C10 | 1/4-type Color CMOS Image Sensor with 110 k Pixels |
| LZ85194 | IrDA Control Peripheral Engine(IrDA 控制外圍處理器) |
| LZ8519X | IrDA Control Peripheral Engine (PE) |
| LZ85202 | IrDA Control Host Controller with USB Interface(帶USB接口的IrDA控制主控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LZ-24-C | 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
| LZ-24E | 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
| LZ-24E-HV | 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
| LZ-24E-K | 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
| LZ-24E-K-HV | 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
發布緊急采購，3分鐘左右您將得到回復。