參數資料
型號： LX1563IDM-TR
廠商： MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP
元件分類： 穩壓器
英文描述： 0.5 A POWER FACTOR CONTROLLER, PDSO8
封裝： ROHS COMPLIANT, PLASTIC, SOIC-8
文件頁數： 6/25頁
文件大小： 430K
代理商： LX1563IDM-TR
SECOND-GENERATION POWER FACTOR C ONTROLLER
LX1562/1563
PRODUCT DA T ABOOK 1996/1997
Copyright 1996
Rev. 1.3a
8/30
14
P RODUCTION D ATA
S HEET
IC DESCRIPTION
ERROR AMPLIFIER
The error amplifier is an internally compensated op-amp with
access to the inverting input and the output pin.
The non-
inverting input is internally connected to the voltage reference
and is not available for external connection. The amplifier is
designed for an open loop gain of 80dB, along with a typical
bandwidth of 1.7MHz and 49 degrees of phase margin. The
boost output voltage of the power factor pre-regulator is di-
vided down and monitored by the inverting input. Input bias
current (0.5A max) can cause an output voltage error that is
equal to the product of the input bias current and the value of
the upper divider resistor. The amplifier's output is available
for external loop compensation. Typically, the loop bandwidth
is set below 10Hz in order to reject the low frequency ripple
associated with 2X the line frequency.
For example, if the
error amplifier is configured as an integrator with 1.2Hz band-
width, it will have 40dB ripple rejection at 120Hz frequency.
This means that if the output of the error amp is allowed to
have 100mV of ripple, the boost converter must be limited to
less than 10V of ripple on its output.
To prevent boost output run away condition that may occur
during removal of the output load, a separate comparator moni-
tors the E.A. output voltage and compares it to an internal 1.8V
reference. When load is removed, E.A. output swings lower
than 1.8V, trips the comparator and turns output driver off till
the inverting input voltage drops below 2.5V. At this point, the
E.A. output swings positive, turns the output driver back on
and repeats the cycle until the load is returned to normal con-
dition.
To reduce output overshoot during line and load transients,
the E.A. output is clamped to two diode drops above the refer-
ence voltage.
This prohibits the amplifier from being satu-
rated, allowing it to recover faster thus minimizing the boost
voltage overshoot.
VOLTAGE REFERENCE
(continued)
V
HYST
C1
DISCHARGE
V
START
BOOTSTRAP
WINDING
R
T & CT TIME CONSTANT
V
C1
t
DISCHARGE
TIME
FIGURE 25 — START-UP CAPACITOR VOLTAGE
VOLTAGE REFERENCE
The voltage reference is a low drift bandgap design which pro-
vides a stable +2.5V output with maximum of ±1.5% initial ac-
curacy. This voltage is internally tied to the non-inverting in-
put of the amplifier and is not available for external connec-
tion. The initial accuracy of the reference includes error am-
plifier input offset voltage. Figure 26 shows typical variation of
the reference voltage vs. temperature.
FIGURE 27 — THE AMPLIFIER CONFIGURED AS AN INTEGRATOR
FOR LOOP COMPENSATION
From I
DET Logic
1.8V
OUTPUT
DRIVE
7
1
2
V
REF
C4
V
O
I
9
R9
R10
Bias
BW =
1
2
π R
9 C4
I
9 >> IBIAS
2f
f = Line Freq.
2.47
2.45
(T
A)
Ambient Temperature - (°C)
2.52
(V
R)
Reference
Voltage
-
(V)
2.48
-50
-25
0
25
50
75
100
125
V
CC = 12V
C
L = 1nF
2.46
2.49
2.50
2.51
FIGURE 26 — REFERENCE VOLTAGE (Including Offset) vs. TEMPERATURE
O
B
SO
LETE
PRO
D
UCT
NOT
RECOMMENDED
FOR
NEW
DESIGNS
相關PDF資料
PDF描述
LX1562IM 0.5 A POWER FACTOR CONTROLLER, PDIP8
LX1562IDM 0.5 A POWER FACTOR CONTROLLER, PDSO8
LX1570IDM-TR 1 A SWITCHING CONTROLLER, PDSO8
LX1571CDM-TR 1 A SWITCHING CONTROLLER, PDSO8
LX1571IDM-TR 1 A SWITCHING CONTROLLER, PDSO8
相關代理商/技術參數
參數描述
LX1563IM 功能描述:IC CONTROLLER PFC 9.8V 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - PFC（功率因數修正） 系列:- 產品培訓模塊:GreenChip Synchronous Rectification Control Family of ICs 標準包裝:1 系列:- 模式:間歇導電（DCM） 頻率 - 開關:- 電流 - 啟動:- 電源電壓:8.6 V ~ 38 V 工作溫度:-20°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:Digi-Reel® 其它名稱:568-5348-6
LX1570 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:PHASE MODULATED AC SYNCHRONOUS SECONDARY-SIDE CONTROLLER
LX1570CDM 功能描述:IC REG CTRLR ISO PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR)
LX1570CM 功能描述:IC REG CTRLR ISO PWM CM 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR)
LX1570IDM 功能描述:IC REG CTRLR ISO PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*