- 您現在的位置：買賣IC網 > PDF目錄45001 > LV8731V STEPPER MOTOR CONTROLLER, PDSO44 PDF資料下載
參數資料
| 型號： | LV8731V |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO44 |
| 封裝： | 0.275 INCH, SSOP-44 |
| 文件頁數： | 15/26頁 |
| 文件大?。?/td> | 336K |
| 代理商： | LV8731V |
LV8731V
No.A1482-22/26
(3) Auto reset type
In the automatic reset mode, when the output current exceeds the detection current level, the output waveform
changes to the switching waveform.
As with the latch system, when the output short-circuited state is detected, the short-circuit protection circuit is
activated. When the operation of the short-circuit detection circuit exceeds the timer latch time (Tcem) described later,
the output is changed over to the standby mode and is reset to the ON mode again in 2ms (typ). In this event, if the
overcurrent mode still continues, the switching mode described above is repeated until the overcurrent mode is
canceled.
(4) Unusual condition warning output pins (EMO, MONI)
The LV8731V is provided with the EMO pin which notifies the CPU of an unusual condition if the protection circuit
operates by detecting an unusual condition of the IC. This pin is of the open-drain output type and when an unusual
condition is detected, the EMO output is placed in the ON (EMO = Low) state.
In the DC motor driver mode (DM = High), the MONI pin also functions as a warning output pin.
The functions of the EMO pin and MONI pin change as shown below depending on the state of the DM pin.
When the DM is low (STM mode) :
EMO : Unusual condition warning output pin
MONI : Excitation initial position detection monitoring
When the DM is high (DCM) mode) :
EMO : Channel 1 warning output pin
MONI : Channel 2 warning output pin
Furthermore, the EMO (MONI) pin is placed in the ON state when one of the following conditions occurs.
1. Shorting-to-power, shorting-to-ground, or shorting-to-load occurs at the output pin and the output short-circuit
protection circuit is activated.
2. The IC junction temperature rises and the thermal protection circuit is activated.
DM = L (STM mode)
DM = H (DCM mode)
Unusual condition
EMO
MONI
EMO
MONI
Channel 1 short-circuit detected
ON
-
ON
-
Channel 2 short-circuit detected
ON
-
ON
Overheating condition detected
ON
-
ON
(5) Timer latch time (Tcem)
The time taken for the output to be set to OFF when the output has been short-circuited can be set using capacitor
Ccem, connected between the CEM pin and GND. The value of capacitor Ccem is determined by the formula given
below.
Timer latch : Tcem
Tcem
≈ Ccem × Vtcem/Icem [sec]
Vtcem : Comparator threshold voltage, typ 1V
Icem : CEM pin charge current, typ 10
μA
相關PDF資料 |
PDF描述 |
|---|---|
| LV8743V | 0.8 A SWITCHING CONTROLLER, 440 kHz SWITCHING FREQ-MAX, PDSO44 |
| LV8743V | 0.8 A SWITCHING CONTROLLER, 440 kHz SWITCHING FREQ-MAX, PDSO44 |
| LV8746V | STEPPER MOTOR CONTROLLER, 1.2 A, PDSO44 |
| LV8746V | STEPPER MOTOR CONTROLLER, 1.2 A, PDSO44 |
| LV8747T | 1.75 A SWITCHING CONTROLLER, 150 kHz SWITCHING FREQ-MAX, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV8731VGEVB | 功能描述:電源管理IC開發工具 EVM FOR LV8731V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LV8731V-MPB-H | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LV8731V-TLM-H | 功能描述:馬達/運動/點火控制器和驅動器 9-32VSteppingMotor 2chBrush Motor Dr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LV8732V | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Constant-Current Control Stepping Motor Driver |
| LV8732V_10 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Constant-Current Control Stepping Motor Driver |
發布緊急采購，3分鐘左右您將得到回復。