- 您現在的位置：買賣IC網 > PDF目錄45001 > LV8057GR STEPPER MOTOR CONTROLLER, 0.6 A, QCC28 PDF資料下載
參數資料
| 型號： | LV8057GR |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.6 A, QCC28 |
| 封裝： | 3.50 X 3.50 MM, VCT-28 |
| 文件頁數： | 9/25頁 |
| 文件大小： | 258K |
| 代理商： | LV8057GR |
LV8057GR
No.A1027-17/25
The PWM Duty Setting
The PWM Duty can be selected from 32 stages between 51.6% and 100%.
Power-saving and efficient drive are possible by Duty control.
Also, the coil current value at Slow Decay is determined by the following formula.
(Coil current value) =
(Motor supply voltage VB1)
× (DUTY)
(Coil resistance RL)(*)
(*) : Measurements are subject to the influence of ON resistance of the output transistor and internal resistance of the
measuring system.
DC Motor Drive Method (Channel 1)
The channel 1 is a PWM control output. The Duty pulse from 51.6 to 100% is generated based on the pulse generated in
the pulse generation circuit in IC. Therefore, the PWM signal is output by the H bridge circuit.
The Duty setting is performed by serial communications. And, the PWM frequency can be adjusted in four levels.
In addition, the PWM mode can be set with either Fast Decay or Slow Decay by serial communications.
When channel 1 is used to drive a DC motor, the drive polarity is set by serial communications.
As for the brake, setting by serial communications and the BRK pin control are possible.
PWM Control Settings (Channels 2 and 3)
The channels 2 and 3 are the PWM control outputs.
Various setting of the PWM signal is performed by serial communications, along with channel 1.
The PWM frequency is common to channel 1.
Voice Coil Motor Drive Method (Channels 4 and 5)
The channels 4 and 5 are constant current outputs. The OUT8 pin is shared by the channels 4 and 5.
However, both channels can not be driven at the same time.
When channel 4 is used to drive a voice coil motor, the drive polarity is set by serial communications.
On the other hand, when channel 5 is used to drive a voice coil motor, 1 line control of the IN51/ENA pin by
combination of the serial communications can be used to set the drive polarity.
Setting Procedure :
(1) The drive polarity is set by the serial data (D0/1/2/3/4/5/6/7 = 1/0/0/1/
#/#/*/*).
(3) The drive on/off state is set by the input signal (output enable signal) of the IN51/ENA pin.
Constant Current Control Settings (Channels 4 and 5)
The constant current settings for the channels 4 and 5 are set by the serial communications.
The output constant current value is determined by the constant current reference voltage set with the serial data and the
resistor (RF) connected between the RF1 pin and GND.
The following formula can be used to calculate the output constant current.
(output constant current) = (constant current reference voltage) / (value of the resistance RF)
In addition, the resistor (RF) is shared by the channels 4 and 5. So, if a different current value is set in the channels 4 and
5, it is necessary to switch each reference voltage by the serial communications.
相關PDF資料 |
PDF描述 |
|---|---|
| LV8105W | BRUSHLESS DC MOTOR CONTROLLER, 0.02 A, PQFP48 |
| LV8414CS | STEPPER MOTOR CONTROLLER, 0.6 A, PBGA32 |
| LV8481CS | STEPPER MOTOR CONTROLLER, PBGA10 |
| LV8731V | STEPPER MOTOR CONTROLLER, PDSO44 |
| LV8743V | 0.8 A SWITCHING CONTROLLER, 440 kHz SWITCHING FREQ-MAX, PDSO44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV8062FA-AH | 功能描述:馬達/運動/點火控制器和驅動器 BRUSHLESS MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LV8063FA | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Single-Phase Full-Wave Driver |
| LV8063FA-BH | 功能描述:馬達/運動/點火控制器和驅動器 FAN MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LV8063TT | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Fan Motor Driver Single-Phase Full-Wave Driver |
| LV8063TT-TLM-H | 功能描述:馬達/運動/點火控制器和驅動器 FAN MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。