- 您現在的位置：買賣IC網 > PDF目錄384633 > LTC4416 (Linear Technology Corporation) 36V, Low Loss Dual PowerPath Controllers for Large PFETs PDF資料下載
參數資料
| 型號： | LTC4416 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 36V, Low Loss Dual PowerPath Controllers for Large PFETs |
| 中文描述： | 36V的，低損耗電源通路大型雙電源通路控制器 |
| 文件頁數： | 7/12頁 |
| 文件大小： | 201K |
| 代理商： | LTC4416 |
LTC4416/LTC4416-1
4416fa
OPERATIOU
The band-gap reference provides internal bias currents
used by the channel 1 and channel 2 controllers. It also
provides a precision voltage reference, V
REF
, used by com-
parators C1 and C2. The band-gap reference is powered
as long as a minimum operational voltage is present on
either V1, V2, or V
S
.
The C1 and C2 comparators provide a fixed comparison
between the E1 and E2 inputs, respectively, and the in-
ternal V
REF
signal. The comparator outputs are directly
represented by the H1 and H2 open-drain outputs. The
output states of H1 and H2 are not dependent upon
the relative voltage difference between V
V1
– V
VS
and
V
V2
– V
VS
, respectively. If V
E1
is less than V
REF
, the H1
open-drain output will be low impedance to GND. If V
E2
is less than V
REF
, the H2 open-drain output will be low
impedance to GND.
The A1 and A2 circuits act both as a high side
transconductance amplifiers and as comparators. Both
A1 and A2 act identically when the analog controllers
are fully enabled. The relationship of the G1 current is
represented by Figure 1.
When V
V1
– V
VS
< V
RTO
, the A1 activates the reverse turn-
off condition and the I
G1
current is I
G(OFF)
. When V
RTO
<
V
V1
– V
VS
< V
FR
, the A1 acts as a class A output and the
I
G1
current is fixed at I
G(SRC)
. As the V
V1
– V
VS
voltage
V
V1
– V
VS
4416 F01
I
G1
V
RTO
V
FR
V
FON
I
GFON(SNK)
I
G(SNK)
I
G(SRC)
I
G(OFF)
NOT DRAWN TO SCALE
Figure 1. I
G1
vs V
V1
– V
VS
approaches the forward regulation voltage, V
FR
, the I
G(SNK)
current will be proportional to V
V1
– V
VS
. When V
V1
– V
VS
> V
FON
, the A1 activates the fast-on condition, t
G(ON)
, and
the I
G1
current is set to I
GFON(SNK)
.
LTC4416 OPERATION
The interaction of the LTC4416 analog controllers distin-
guish the operation of the LTC4416 from a simple circuit
using two PowerPath controllers. Table 1 explains the
different operation modes of the analog controllers.
Table 1. LTC4416 Operational Modes
E1
E2
Operation Mode
1
0
Load Sharing
1
Sense
V1 is Less Than V2
Sense
0
V1 is Greater Than V2
0
X
Channel 1 Disabled.
Do Not Use
X
1
Channel 2 Disabled.
Do Not Use
0
1
Both Channels Disabled
I
G(OFF)1
Enabled
Enabled
I
G(OFF)2
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
The LTC4416 has six modes of operation. Each mode of
operation is dependent upon the configuration of the E1
and E2 input pins.
Load Sharing Operation
The load sharing mode configures the LTC4416 into two
independent PowerPath controllers. This is accomplished
by fully enabling both the first analog controller and the
second analog controller. Both channels will implement
the gate drive outlined in Figure 1.
V1 is Less Than V2 Operation
Channel 1 is fully enabled. If V
V1
– V
VS
< V
RTO
, channel 1
will implement all of the I
G1
currents listed in Figure 1.
When V
E2
is above the V
REF
threshold, channel 2 is in a
“soft-off mode”. This means that G2 will only provide an
I
G(SRC)
current instead of either an I
G(SRC)
or an I
G(OFF)
current.
When V
E2
is below the V
REF
threshold, channel 2 is fully
enabled, and G2 will become active implementing the I
G
output current listed in Figure 1.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4416-1 | 36V, Low Loss Dual PowerPath Controllers for Large PFETs |
| LTC4416EMS | 36V, Low Loss Dual PowerPath Controllers for Large PFETs |
| LTC4416EMS-1 | 36V, Low Loss Dual PowerPath Controllers for Large PFETs |
| LTC4416IMS | 36V, Low Loss Dual PowerPath Controllers for Large PFETs |
| LTC4416IMS-1 | 36V, Low Loss Dual PowerPath Controllers for Large PFETs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4416EMS | 制造商:Linear Technology 功能描述:OR Controller P-Channel Dual-OUT 10-Pin MSOP |
| LTC4416EMS#PBF | 功能描述:IC CTLR POWERPATH 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 標準包裝:1,000 系列:- 應用:電池備份，工業/汽車，大電流開關 FET 型:- 輸出數:5 內部開關:是 延遲時間 - 開啟:100ns 延遲時間 - 關閉:- 電源電壓:3 V ~ 5.5 V 電流 - 電源:250µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:帶卷 (TR) |
| LTC4416EMS#TRPBF | 功能描述:IC CNTRLR POWERPATH 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 標準包裝:1,000 系列:- 應用:電池備份，工業/汽車，大電流開關 FET 型:- 輸出數:5 內部開關:是 延遲時間 - 開啟:100ns 延遲時間 - 關閉:- 電源電壓:3 V ~ 5.5 V 電流 - 電源:250µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:帶卷 (TR) |
| LTC4416EMS-1 | 制造商:Linear Technology 功能描述:OR Controller P-Channel Dual-OUT 10-Pin MSOP |
| LTC4416EMS-1#PBF | 功能描述:IC CNTRLR POWERPATH 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 標準包裝:1,000 系列:- 應用:電池備份，工業/汽車，大電流開關 FET 型:- 輸出數:5 內部開關:是 延遲時間 - 開啟:100ns 延遲時間 - 關閉:- 電源電壓:3 V ~ 5.5 V 電流 - 電源:250µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。