參數資料
型號: LTC4264CDE
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: 1.65 A SWITCHING CONTROLLER, PDSO12
封裝: 4 X 3 MM, PLASTIC, MO-229WGED, DFN-12
文件頁數: 14/24頁
文件大?。?/td> 304K
代理商: LTC4264CDE
LTC4264
21
4264f
APPLICATIONS INFORMATION
VOUT, to avoid the possibility of leakage shutting down the
LTC4264. If not used, tie SHDN to VIN.
The load capacitor connected between GND and VOUT
of the LTC4264 can store signicant energy when fully
charged. The design of a PD must ensure that this en-
ergy is not inadvertently dissipated in the LTC4264. The
polarity-protection diodes prevent an accidental short
on the cable from causing damage. However, if the VIN
pin is shorted to GND inside the PD while the capacitor
is charged, current will ow through the parasitic body
diode of the internal MOSFET and may cause permanent
damage to the LTC4264.
ELECTRO STATIC DISCHARGE AND SURGE
PROTECTION
The LTC4264 is specied to operate with an absolute
maximum voltage of –90V and is designed to tolerate brief
over-voltage events. However, the pins that interface to the
outside world (primarily VIN and GND) can routinely see
peak voltages in excess of 10kV. To protect the LTC4264,
it is highly recommended that the SMAJ58A unidirectional
58V transient voltage suppressor be installed between the
diode bridge and the LTC4264 (D3 in Figure 4).
ISOLATION
The 802.3 standard requires Ethernet ports to be electrically
isolated from all other conductors that are user accessible.
This includes the metal chassis, other connectors and
any auxiliary power connection. For PDs, there are two
common methods to meet the isolation requirement. If
there will be any user accessible connection to the PD,
then an isolated DC/DC converter is necessary to meet
the isolation requirements. If user connections can be
avoided, then it is possible to meet the safety requirement
by completely enclosing the PD in an insulated housing.
In all PD applications, there should be no user accessible
electrical connections to the LTC4264 or support circuitry
other than the RJ-45 port.
相關PDF資料
PDF描述
LTC4266AIUHF-4#TRPBF POWER SUPPLY MANAGEMENT CKT, PQCC38
LTC4266AIUHF-3#PBF POWER SUPPLY MANAGEMENT CKT, PQCC38
LTC4266AIUHF-1#PBF POWER SUPPLY MANAGEMENT CKT, PQCC38
LTC4266AIUHF-1#TRPBF POWER SUPPLY MANAGEMENT CKT, PQCC38
LTC4266CIUHF#PBF POWER SUPPLY MANAGEMENT CKT, PQCC38
相關代理商/技術參數
參數描述
LTC4264CDE#PBF 功能描述:IC CNTRLR PD INTERFACE 12-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4264CDE#TRPBF 功能描述:IC INTERFACE 802.3AT 12-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4264IDE 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Power PD Interface Controller with 750mA Current Limit
LTC4264IDE#PBF 功能描述:IC CNTRLR PD INTERFACE 12-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4264IDE#TRPBF 功能描述:IC CNTRLR PD INTERFACE 12-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C,串行,SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN(4x4) 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND