- 您現在的位置：買賣IC網 > PDF目錄179919 > LTC4259AIGW-1#PBF (LINEAR TECHNOLOGY CORP) Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: -40°C to +85°C PDF資料下載
參數資料
| 型號： | LTC4259AIGW-1#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: -40°C to +85°C |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 |
| 封裝： | 0.300 INCH, LEAD FREE, PLASTIC, SSOP-36 |
| 文件頁數： | 5/32頁 |
| 文件大小： | 416K |
| 代理商： | LTC4259AIGW-1#PBF |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4259A-1
13
4259a1fa
involves reading the register to determine its status, set-
ting the appropriate bit in software and writing back the
entire register, a pushbutton register allows a single bit to
be written without knowing or affecting the status of the
other bits in the register. Pushbutton registers are write-
only and will return 00h if read.
Det/Class Restart PB (Address 18h): Detection/Classifi-
cation Restart Pushbutton Register, Write Only. Writing a
1 to any bit in this register will start or restart a single
detection or classification cycle at the corresponding port
in Manual mode. It can also be used to set the correspond-
ing bits in the Detect/Class Enable register (address 14h)
for ports in auto or semiauto mode. The lower 4 bits affect
detection on each port while the upper 4 bits affect
classification.
Power Enable PB (Address 19h): Power Enable Pushbutton
Register, Write Only. The lower four bits of this register set
the Power Enable bit in the corresponding Port Status reg-
ister; the upper four bits clear the corresponding Power
Enable bit. Setting or clearing the Power Enable bits via this
register will turn on or off the power in any mode except
shutdown, regardless of the state of detection or classifi-
cation. Note that tICUT, tSTART and disconnect events (if
enabled) will still turn off power if they occur.
The Power Enable bit cannot be set if the port has turned
off due to a tICUT or tSTART fault and the tICUT timer has not
yet counted back to zero. See Applications Information for
more information on tICUT timing.
Clearing the Power Enable bits with this register also
clears the detect and fault event bits, the Port Status
register, and the Detection and Classification Enable bits
for the affected port(s).
Reset PB (Address 1Ah): Reset Pushbutton, Write Only.
Bits 0-3 reset the corresponding port by clearing the power
enable bit, the detect and fault event bits, the status regis-
ter and the detection and classification enable bits for that
port. Bit 4 returns the entire LTC4259A-1 to the power-on
reset state; all ports are turned off, the AUTO pin is reread
and all registers are returned to their power-on defaults,
except VDDUVLO, which remains cleared. Bit 5 is reserved;
setting it has no effect. Setting bit 6 releases the Interrupt
pin if it is asserted without affecting the Event registers or
the Interrupt register. When the INT pin is released in this
Detect/Class Enable (Address 14h): Detection and Clas-
sification Enable, Read/Write. The lower four bits of this reg-
ister enable the detection circuitry at the corresponding port
if that port is in Auto or Semiauto mode. The upper four bits
enable the classification circuitry at the corresponding port
if that port is in Auto or Semiauto mode. In manual mode,
setting a bit in this register will cause the LTC4259A-1 to
perform one classification or detection cycle on the corre-
sponding port. Writing to the Detect/Class Restart PB (18h)
has the same effect without disturbing the Detect/Class
Enable bits for other ports.
Timing Config (Address 16h):Global Timing Configuration,
Read/Write. Bits 0-1 program tDIS, the time duration before
a port is automatically tuned off after the PD is removed.
The LTC4259A-1 can be programmed to monitor whether
port current is below IMIN (DC connect) or port impedance
is high (AC disconnect). Bits 2-3 program tICUT, the time
during which a port’s current can exceed ICUT without it
being turned off. If the current is still above ICUT after tICUT,
the LTC4259A-1 will indicate a tICUT fault and turn the port
off. Bits 4-5 program tSTART, the time duration before an
overcurrent condition during port power-on is considered
a tSTART fault and the port is turned off. Note that using the
tICUT and tSTART times other than the default is not compli-
ant with IEEE 802.3af and may double or quadruple the
energy dissipated by the external MOSFETs during fault con-
ditions. Bits 6-7 are reserved and should be read/written
as 0. See Electrical Characteristics for timer bit encoding.
Also see the Applications Information for descriptions of
tSTART, tICUT, DC and AC disconnect timing.
Misc Config (Address 17h): Miscellaneous Configuration,
Read/Write. Bit 5 is the Osc Fail Mask; it is set by default.
When the Osc Fail Mask bit is clear, it prevents a failure on
the OSCIN pin from setting the Osc Fail bit and causing a
Supply Event Interrupt. Setting bit 7 enables the INT pin.
If this bit is reset, the LTC4259A-1 will not pull down the
INT pin in any condition nor will it respond to the Alert Re-
sponse Address. This bit is set by default.
Pushbutton Registers
Note Regarding Pushbutton Registers: “Pushbutton” reg-
isters are specialized registers that trigger an event when
a 1 is written to a bit; writing a 0 to a bit will do nothing. Unlike
a standard read/write register, where setting a single bit
REGISTER FU CTIO S
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4259AIGW-1#TRPBF | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: -40°C to +85°C |
| LTC4259ACGW#PBF | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C |
| LTC4259ACGW#TRPBF | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C |
| LTC4261CUFD#TRPBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: QFN; No of Pins: 24; Temperature Range: 0°C to +70°C |
| LTC4261CUFD-2#PBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: QFN; No of Pins: 24; Temperature Range: 0°C to +70°C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4259CGW-ES | 制造商:LINEAR_TECH 功能描述: |
| LTC4260 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:UV, OV and Reverse Supply Protection Controller Low Operating Current: 125μA |
| LTC4260CGN | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 80V 24-Pin SSOP N |
| LTC4260CGN#PBF | 功能描述:IC CTLR HOT SWAP I2C 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4260CGN#TR | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 80V 24-Pin SSOP N T/R |
發布緊急采購，3分鐘左右您將得到回復。