- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4227IGN-1#PBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY MANAGEMENT CKT, PDSO16 PDF資料下載
參數資料
| 型號： | LTC4227IGN-1#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| 封裝： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16 |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 307K |
| 代理商： | LTC4227IGN-1#PBF |
LTC4227-1/LTC4227-2
13
422712f
applicaTions inForMaTion
Active Current Loop Stability
The active current loop on the HGATE pin is compensated
by the parasitic gate capacitance of the external N-channel
MOSFET. No further compensation components are nor-
mally required. In the case when a MOSFET with CISS ≤
2nF is chosen, an RHG and CHG compensation network
connected at the HGATE pin may be required. The value
of CHG is selected based on the inrush current allowed for
the output load capacitance. The resistor, RHG, connected
in series with CHG accelerates the MOSFET gate recovery
for active current limiting after a fast gate pull-down due
to an output short. The value of CHG should be ≤100nF
and RHG should be between 10Ω and 100Ω for optimum
performance.
TMR Pin Functions
An external capacitor, CT, connected from the TMR pin to
GND serves as fault filtering when the supply output is in
active current limit. When the voltage across the sense
resistor exceeds the circuit breaker trip threshold (50mV),
TMR pulls up with 100A. Otherwise, it pulls down with
2A. The fault filter times out when the 1.235V TMR
threshold is exceeded, causing the corresponding FAULT
pin to pull low. The fault filter delay or circuit breaker time
delay is:
tCB = CT 12[ms/F].
After the circuit breaker timeout, the TMR pin capacitor
pulls down with 2A from the 1.235V TMR threshold
until it reaches 0.2V. Then, it completes 14 cooling cycles
consisting of the TMR pin capacitor charging to 1.235V
with a 100A current and discharging to 0.2V with a 2A
current. At that point, the HGATE pin voltage is allowed to
start up if the fault has been cleared as described in the
Resetting Faults section. When the latched fault is cleared
during the cool-off period, the corresponding FAULT pin
pulls high. The total cool-off time for the MOSFET after
an overcurrent fault is:
tCOOL = CT 11[s/F]
If the latched fault is not cleared after the cool-off period,
the cooling cycles continue until the fault is cleared.
After the cool-off period, the HGATE pin is only allowed to
pull up if the fault has been cleared for the latch-off part
(LTC4227-1). For the auto-retry part (LTC4227-2), the
latched fault is cleared automatically following the cool-off
period and the HGATE pin voltage is allowed to restart.
Resetting Faults (LTC4227-1)
For the latch-off part (LTC4227-1), an overcurrent fault is
latched after tripping the circuit breaker, and the FAULT
pin is asserted low. Only the Hot Swap MOSFET is turned
off and the ideal diode MOSFETs are not affected.
To reset a latched fault and restart the output, pull the ON
pin below 0.6V for more than 100s and then high above
1.235V. The fault latches reset and the FAULT pin deas-
serts on the falling edge of the ON pin. When ON goes
high again, a 100ms debounce cycle is initiated before
the HGATE pin voltage restarts. Toggling the EN pin high
and then low again also resets a fault, but the FAULT pin
pulls high at the end of the 100ms debounce cycle before
the HGATE pin voltage starts up. Bringing all the supplies
below the INTVCC undervoltage lockout threshold (2.2V)
shuts off all the MOSFETs and resets all the fault latches.
A 100ms debounce cycle is initiated before a normal
start-up when any of the supplies is restored above the
INTVCC UVLO threshold.
Auto-Retry After a Fault (LTC4227-2)
Fortheauto-retrypart(LTC4227-2),thelatchedfaultisreset
automatically after a cool-off timing cycle as described in
the TMR Pin Functions section. At the end of the cool-off
period, the fault latch is cleared and FAULT pulls high. The
HGATE pin voltage is allowed to start up and turn on the
Hot Swap MOSFET. If the output short persists, the supply
powers up into a short with active current limiting until the
circuit breaker times out and FAULT again pulls low. A new
cool-off cycle begins with TMR ramping down with a 2A
current. The whole process repeats itself until the output
short is removed. Since tCB and tCOOL are a function of
TMR capacitance, CT,the auto-retry duty cycle is equal to
0.1%, irrespective of CT.
Figure6showsanauto-retrysequenceafteranovercurrent
fault.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4227CUFD-1#TRPBF | POWER SUPPLY MANAGEMENT CKT, PQCC20 |
| LTC4227CUFD-2#TRPBF | POWER SUPPLY MANAGEMENT CKT, PQCC20 |
| LTC4227IGN-1#TRPBF | POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| LTC4227CUFD-1#PBF | POWER SUPPLY MANAGEMENT CKT, PQCC20 |
| LTC4227IUFD-2#PBF | POWER SUPPLY MANAGEMENT CKT, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4227IGN-2#PBF | 功能描述:IC CONTROLLER HOT SWAP 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4227IGN-2#TRPBF | 功能描述:IC CTRLR HOT SWAP 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4227IUFD-1#PBF | 功能描述:IC CONTROLLER HOT SWAP 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4227IUFD-1#TRPBF | 功能描述:IC CTRLR HOT SWAP 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4227IUFD-2#PBF | 功能描述:IC CONTROLLER HOT SWAP 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。