- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4098EPDC-1#PBF (LINEAR TECHNOLOGY CORP) BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | LTC4098EPDC-1#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 4 X 3 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-20 |
| 文件頁數： | 32/32頁 |
| 文件大?。?/td> | 443K |
| 代理商： | LTC4098EPDC-1#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁
LTC4098/LTC4098-1
9
40981fc
OVSENS (Pin 1): Overvoltage Protection Sense Input.
OVSENS should be connected through a 6.04k resistor
to the input power connector and the drain of an external
N-channel MOS pass transistor. When the voltage on this
pin exceeds a preset level, the OVGATE pin will be pulled
to GND to disable the pass transistor and protect down-
stream circuitry. If overvoltage protection is not desired,
connect OVSENS to GND.
OVGATE (Pin 2): Overvoltage Protection Gate Output.
Connect OVGATE to the gate pin of an external N-channel
MOS pass transistor. The source of the transistor should
be connected to VBUS and the drain should be connected
to the product’s DC input connector. This pin is connected
to an internal charge pump capable of creating sufficient
overdrive to fully enhance the pass transistor. If an over-
voltage condition is detected, OVGATE is brought rapidly
to GND to prevent damage to downstream circuitry. OV-
GATE works in conjunction with OVSENS to provide this
protection. If overvoltage protection is not desired, leave
OVGATE open.
CLPROG (Pin 3): USB Current Limit Program and Monitor
Pin. A 1% resistor from CLPROG to ground determines
the upper limit of the current drawn from the VBUS pin.
A precise fraction of the input current, hCLPROG, is sent
to the CLPROG pin when the high side switch is on. The
switching regulator delivers power until the CLPROG
pin reaches 1.188V. Therefore, the current drawn from
VBUS will be limited to an amount given by hCLPROG and
RCLPROG. There are several ratios for hCLPROG available,
two of which correspond to the 500mA and 100mA USB
specifications. A multilayer ceramic averaging capacitor
is also required at CLPROG for filtering.
NTCBIAS (Pin 4): NTC Thermistor Bias Output. If NTC
operation is desired, connect a bias resistor between
NTCBIAS and NTC, and an NTC thermistor between NTC
and GND. To disable NTC operation, connect NTC to GND
and leave NTCBIAS open.
NTC (Pin 5): Input to the NTC Thermistor Monitoring
Circuits. The NTC pin connects to a negative temperature
coefficient thermistor which is typically co-packaged with
the battery pack to determine if the battery is too hot or too
cold to charge. If the battery’s temperature is out of range,
charging is paused until the battery temperature re-enters
the valid range. A low drift bias resistor is required from
NTCBIAS to NTC and a thermistor is required from NTC
to ground. If the NTC function is not desired, the NTC pin
should be grounded.
BATSENS (Pin 6): Battery Voltage Sense Input. For proper
operation, this pin must always be connected to BAT. For
best performance, connect BATSENS to BAT physically
close to the Li-Ion cell.
PROG (Pin 7): Charge Current Program and Charge Cur-
rent Monitor Pin. Connecting a 1% resistor from PROG
to ground programs the charge current. If sufficient input
power is available in constant-current mode, this pin servos
to 1V. The voltage on this pin always represents the actual
charge current by using the following formula:
IBAT =
VPROG
RPROG
1030
CHRG (Pin 8): Open-Drain Charge Status Output. The
CHRG pin indicates the status of the battery charger. Four
possible states are represented by CHRG: charging, not
charging, unresponsive battery and battery temperature
out of range. CHRG is modulated at 35kHz and switches
between a low and a high duty cycle for easy recognition
by either humans or microprocessors. CHRG requires a
pull-up resistor and/or LED to provide indication.
GND (Pin 9, 21): Exposed Pad and pin must be soldered
to the PCB to provide a low electrical and thermal imped-
ance connection to ground.
IDGATE (Pin 10): Ideal Diode Amplifier Output. This pin
controls the gate of an external P-channel MOSFET transis-
tor used to supplement the internal ideal diode. The source
of the P-channel MOSFET should be connected to VOUT
and the drain should be connected to BAT.
BAT (Pin 11): Single-Cell Li-Ion Battery Pin. Depending
on available power and load, a Li-Ion battery on BAT will
either deliver system power to VOUT through the ideal diode
or be charged from the battery charger. The LTC4098 will
charge to a maximum voltage of 4.200V. The LTC4098-1
will charge to a maximum voltage of 4.100V.
PIN FUNCTIONS
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4098EUDC-1#PBF | BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4110EUHF#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| LTC4110EUHF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| LTC4151CS-2#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4151HMS#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4098EPDC-1-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:USB Compatible Switching Power Managers/Li-Ion Chargers with Overvoltage Protection |
| LTC4098EPDC-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:USB Compatible Switching Power Managers/Li-Ion Chargers with Overvoltage Protection |
| LTC4098EPDC-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:USB Compatible Switching Power Managers/Li-Ion Chargers with Overvoltage Protection |
| LTC4098EUDC#PBF | 功能描述:IC CHARGER USB COMP 20-UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:Bat-Track™, PowerPath™ 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4098EUDC#TRPBF | 功能描述:IC CHARGER USB COMP 20-UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:Bat-Track™, PowerPath™ 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。