參數資料
型號： LTC4009IUF#TRPBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20
封裝： 4 X 4 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, MO-220WGGD-1, QFN-20
文件頁數： 10/28頁
文件大?。?/td> 351K
代理商： LTC4009IUF#TRPBF
LTC4009
LTC4009-1/LTC4009-2
4009fd
applicaTions inForMaTion
limit value. The second is to make the input current limit
value programmable.
The overall accuracy of this circuit needs to be better than
the power source current tolerance or be margined such
that the worse-case error remains under the power source
limits. The accuracy of the Figure 7 circuit is a function of
theINTVDD,VBE,RCL,RF,R1andR3tolerances.Toimprove
accuracy, the tolerance of RF should be changed from
5.1k, 5% to a 2.49k 1% resistor. RCL and the programming
resistors R1 and R3 should also be 1% tolerance such
that the dominant error is INTVDD (±3%). Bias resistor R2
can be 5%. When choosing NPN transistors, both need
to have good gain (>100) at 10A levels. Low gain NPNs
will increase programming errors. Q1 must be a matched
NPN pair. Since RF has been reduced in value by half, the
capacitor value of CF should double to 0.22F to remain
effective at filtering out any noise.
If you wish to reduce RCL power dissipation for a given
current limit, the programming equation becomes:
R
mV
k
R
I
CL
LIM
=
100
5 2 49
1
–
.
If you wish to make the input current limit programmable,
the equation becomes:
I
mV
k
R
LIM
CL
=
100
5 2 49
1
–
.
The equation governing R2 for both applications is based
on the value of R1. R3 should always be equal to R1.
R2 = 0.875 R1
In many notebook applications, there are situations
where two different ILIM values are needed to allow two
different power adapters or power sources to be used.
In such cases, start by setting RLIM for the high power
ILIM configuration and then use Figure 7 to set the lower
ILIM value. To toggle between the two ILIM values, take
the three ground connections shown in Figure 7, combine
them into one common connection and use a small-signal
NFET (2N7002) to open or close that common connec-
tion to circuit ground. When the NFET is off, the circuit
is defeated (floating) allowing ILIM to be the maximum
value. When the NFET is on, the circuit will become active
and ILIM will drop to the lower set value.
Monitoring Charge Current
The PROG pin voltage can be used to indicate charge cur-
rentwhere1.2085Vindicatesfullprogrammedcurrent(1C)
and zero charge current is approximately equal to RPROG
11.67A. PROG voltage varies in direct proportion to the
chargecurrentbetweenthiszero-current(offset)valueand
1.2085V. When monitoring the PROG pin voltage, using a
buffer amplifier as shown in Figure 8 will minimize charge
current errors. The buffer amplifier may be powered from
the INTVDD pin or any supply that is always on when the
charger is on.
Figure 8. PROG Voltage Buffer
17
13
INTVDD
PROG
<30nA
LTC4009
4009 F08
TO SYSTEM
MONITOR
+
–
C/10 CHRG Indicator
The value chosen for RPROG has a strong influence on
charge current monitoring and the accuracy of the C/10
charge indicator output (CHRG). The LTC4009 uses the
voltageonthePROGpintodeterminewhenchargecurrent
has dropped to the C/10 threshold. The nominal threshold
of 400mV produces an accurate low charge current indi-
cation of C/10 as long as RPROG = 26.7k, independent of
all other current programming considerations. However,
it may sometimes be necessary to deviate from this value
to satisfy other application design goals.
相關PDF資料
PDF描述
LTC4009IUF#PBF BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20
LTC4009CUF-1#TRPBF BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20
LTC4009CUF-2#TRPBF BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20
LTC4009IUF-1#PBF BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20
LTC4009CUF-2#PBF BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20
相關代理商/技術參數
參數描述
LTC4010 制造商:LINEAR 制造商全稱:LINEAR 功能描述:High Efficiency Standalone Nickel Battery Charger
LTC4010CFE 制造商:Linear Technology 功能描述:Battery Charger NiCD/NiMH 16-Pin TSSOP EP
LTC4010CFE#PBF 功能描述:IC CHARGER NIMH/NICD 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2
LTC4010CFE#PBF 制造商:Linear Technology 功能描述:CHARGER BATT NICKEL 34V 16TSSOP 制造商:Linear Technology 功能描述:CHARGER, BATT, NICKEL, 34V, 16TSSOP
LTC4010CFE#TRPBF 功能描述:IC CHARGER NIMH/NICD 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*