- 您現在的位置：買賣IC網 > PDF目錄44995 > LTC3890IGN-1#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, PDSO28 PDF資料下載
參數資料
| 型號： | LTC3890IGN-1#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO28 |
| 封裝： | LEAD FREE, PLASTIC, SSOP-28 |
| 文件頁數： | 8/36頁 |
| 文件大?。?/td> | 498K |
| 代理商： | LTC3890IGN-1#TRPBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC3890-1
16
38901f
APPLICATIONS INFORMATION
Low Value Resistor Current Sensing
A typical sensing circuit using a discrete resistor is shown
in Figure 4a. RSENSE is chosen based on the required
output current.
The current comparator has a maximum threshold
VSENSE(MAX). The current comparator threshold voltage
sets the peak of the inductor current, yielding a maximum
average output current, IMAX, equal to the peak value less
half the peak-to-peak ripple current, ΔIL. To calculate the
sense resistor value, use the equation:
RSENSE =
VSENSE(MAX)
IMAX +
ΔIL
2
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimum value for the Maximum Current Sense Threshold
(VSENSE(MAX)).
When using the controller in very low dropout conditions,
the maximum output current level will be reduced due
to the internal compensation required to meet stability
criterion for buck regulators operating at greater than
50% duty factor. A curve is provided in the Typical Perfor-
mance Characteristics section to estimate this reduction
in peak inductor current depending upon the operating
duty factor.
Inductor DCR Sensing
For applications requiring the highest possible efciency
at high load currents, the LTC3890-1 is capable of sensing
the voltage drop across the inductor DCR, as shown in
Figure 4b. The DCR of the inductor represents the small
amount of DC resistance of the copper wire, which can be
less than 1mΩ for today’s low value, high current inductors.
In a high current application requiring such an inductor,
power loss through a sense resistor would cost several
points of efciency compared to inductor DCR sensing.
If the external (R1||R2) C1 time constant is chosen to be
exactly equal to the L/DCR time constant, the voltage drop
across the external capacitor is equal to the drop across
the inductor DCR multiplied by R2/(R1 + R2). R2 scales the
voltage across the sense terminals for applications where
the DCR is greater than the target sense resistor value.
To properly dimension the external lter components, the
DCR of the inductor must be known. It can be measured
using a good RLC meter, but the DCR tolerance is not
always the same and varies with temperature; consult the
manufacturers’ data sheets for detailed information.
Using the inductor ripple current value from the Inductor
Value Calculation section, the target sense resistor value
is:
RSENSE(EQUIV) =
VSENSE(MAX)
IMAX +
ΔIL
2
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimum value for the Maximum Current Sense Threshold
(VSENSE(MAX)).
Next, determine the DCR of the inductor. When provided,
use the manufacturer’s maximum value, usually given at
20°C. Increase this value to account for the temperature
coefcient of copper resistance, which is approximately
0.4%/°C. A conservative value for TL(MAX) is 100°C.
To scale the maximum inductor DCR to the desired sense
resistor value (RD), use the divider ratio:
R
DCR
at T
D
SENSE EQUIV
MAX
L MAX
=
()
C1 is usually selected to be in the range of 0.1μF to 0.47μF.
This forces R1|| R2 to around 2k, reducing error that might
have been caused by the SENSE+ pin’s ±1μA current.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3890IGN-1#PBF | SWITCHING CONTROLLER, PDSO28 |
| LTC3890MPUH#TRPBF | DUAL SWITCHING CONTROLLER, 585 kHz SWITCHING FREQ-MAX, PQCC32 |
| LTC3890EUH#PBF | DUAL SWITCHING CONTROLLER, 585 kHz SWITCHING FREQ-MAX, PQCC32 |
| LTC3890IUH#TRPBF | DUAL SWITCHING CONTROLLER, 585 kHz SWITCHING FREQ-MAX, PQCC32 |
| LTC3890HUH#PBF | DUAL SWITCHING CONTROLLER, 585 kHz SWITCHING FREQ-MAX, PQCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3890IGN-3#PBF | 制造商:Linear Technology 功能描述:IC REG CTRLR BUCK PWM CM 28SSOP 制造商:Linear Technology 功能描述:DC-DC CONTROLLER BUCK 900KHZ 制造商:Linear Technology 功能描述:BUCK DUAL CNTRL 4-60V 850K 制造商:Linear Technology 功能描述:DC-DC CONTROLLER, BUCK, 900KHZ, SSOP-28 制造商:Linear Technology 功能描述:DC-DC CONTROLLER, BUCK, 900KHZ, SSOP-28; Primary Input Voltage:60V; No. of Outputs:2; No. of Pins:28; Operating Temperature Min:-40C; Operating Temperature Max:125C; Operating Temperature Range:-40C to +125C ;RoHS Compliant: Yes |
| LTC3890IGN-3#TRPBF | 制造商:Linear Technology 功能描述:IC REG CTRLR BUCK PWM CM 28SSOP |
| LTC3890IUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC3890IUH#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC3890IUH-2#PBF | 制造商:Linear Technology 功能描述:DC DC Cntrlr Dual-OUT Sync Step Down 4V to 60V Input 32-Pin QFN EP 制造商:Linear Technology 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN 制造商:Linear Technology 功能描述:DP-SWREG/Controller, High Voltage Dual Output Synchronous Step-Down Controller |
發布緊急采購，3分鐘左右您將得到回復。