參數資料
型號: LTC3537EUD#TRPBF
廠商: Linear Technology
文件頁數: 12/22頁
文件大小: 314K
描述: IC REG DL BST/LINEAR SYNC 16-QFN
標準包裝: 2,500
拓?fù)洌?/td> 升壓(升壓)同步(1),線性(LDO)(1)
功能: 任何功能
輸出數: 2
頻率 - 開關: 2.2MHz
電壓/電流 - 輸出 1: 1.5 V ~ 5.25 V,100mA
電壓/電流 - 輸出 2: 0.6 V ~ 5 V,100mA
帶 LED 驅動器: 無
帶監控器: 無
帶序列發生器:
電源電壓: 0.68 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-WFQFN 裸露焊盤
供應商設備封裝: 16-QFN-EP(3x3)
包裝: 帶卷 (TR)
LTC3537
12
3537fd
OPERATION
Boost Current Limit
The current limit comparator shuts off the N-channel
MOSFET switch once its threshold is reached. The cur-
rent limit comparator delay to output is typically 40ns.
Peak switch current is limited to approximately 750mA,
independent of input or output voltage, unless V
OUTB
 falls
below 0.8V, in which case the current limit is cut in half.
Boost Zero Current Comparator
The zero current comparator monitors the inductor cur-
rent to the output and shuts off the synchronous recti er
when this current reduces to approximately 30mA. This
prevents the inductor current from reversing in polarity,
improving ef ciency at light loads.
Boost Synchronous Recti er
To control inrush current and to prevent the inductor cur-
rent from running away when V
OUTB
 is close to V
INB
, the
P-channel MOSFET synchronous recti er is only enabled
when V
OUTB
 > (V
INB
 + 0.24V).
Boost Anti-Ringing Control
The anti-ringing control connects a resistor across the
inductor to prevent high frequency ringing on the SW pin
during discontinuous current mode operation. Although
the ringing of the resonant circuit formed by L and C
SW
 
(capacitance on SW pin) is low energy, it can cause EMI
radiation.
Boost Output Disconnect
The LTC3537 is designed to allow true output disconnect
by eliminating body diode conduction of the internal P-
channel MOSFET synchronous recti er. This allows V
OUTB
 
to go to zero volts during shutdown, drawing no current
from the input source. It also allows inrush current limit-
ing at turn-on, minimizing surge currents seen by the
input supply. Note that to obtain the advantages of output
disconnect, there cannot be an external Schottky diode
connected between the SW pin and V
OUTB
. The output
disconnect feature also allows V
OUTB
 to be pulled high,
above the nominal regulation voltage, without any reverse
current into the power source connected to V
INB
.
Thermal Overload Protection
If the die temperature exceeds 160癈 typical, the LTC3537
boost converter will shut down. All switches will be off
and the soft-start capacitor will be discharged. The boost
converter will be enabled when the die temperature drops
by approximately 15癈.
BOOST BURST MODE OPERATION
When enabled (MODE pin high), the LTC3537 will auto-
matically enter Burst Mode operation at light load current
and return to  xed frequency PWM mode when the load
increases. Refer to the Typical Performance Characteristics
to see the Burst Mode Threshold Current vs V
INB
. The
load current at which Burst Mode operation is entered can
be changed by adjusting the inductor value. Raising the
inductor value will lower the load current at which Burst
Mode operation is entered.
In Burst Mode operation, the LTC3537 still switches at a
 xed frequency of 2.2MHz, using the same error ampli er
and loop compensation for peak current mode control.
This control method eliminates any output transient when
switching between modes. In Burst Mode operation, en-
ergy is delivered to the output until it reaches the nominal
voltage regulation value, then the LTC3537 transitions to
sleep mode where the outputs are off and the LTC3537
consumes only 30糀 of quiescent current from V
OUTB
 
including the current required to keep the LDO enabled.
When the output voltage droops slightly, switching re-
sumes. This maximizes ef ciency at very light loads by
minimizing switching and quiescent losses. Burst Mode
output voltage ripple, which is typically 1% peak-to-peak,
can be reduced by using more output capacitance (10糉
or greater), or with a small capacitor (10pF to 50pF) con-
nected between V
OUTB
 and FBB.
As the load current increases, the LTC3537 will automati-
cally leave Burst Mode operation. Note that larger output
capacitor values may cause this transition to occur at lighter
loads. Once the LTC3537 has left Burst Mode operation and
returned to normal operation, it will remain there until the
output load is reduced below the burst threshold.
相關PDF資料
PDF描述
LTC3541EDD#TRPBF IC REG DL BCK/LINEAR SYNC 10-DFN
LTC3670EDDB#TRPBF IC REG TRPL BCK/LINEAR 12DFN
LTC3672BEDC-1#TRPBF IC REG TRPL BCK/LINEAR 8-DFN
LTC3700EMS#TRPBF IC REG DL BUCK/LINEAR 10MSOP
LTC4151HMS#TRPBF IC PWR MONITOR MS 80V SD 10MSOP
相關代理商/技術參數
參數描述
LTC3538 制造商:LINER 制造商全稱:Linear Technology 功能描述:800mA Synchronous Buck-Boost DC/DC Converter
LTC3538EDCB 制造商:LINER 制造商全稱:Linear Technology 功能描述:800mA Synchronous Buck-Boost DC/DC Converter
LTC3538EDCB#PBF 制造商:Linear Technology 功能描述:DC-DC CONV BUCK/BOOST 8000mA DFN-8 制造商:Linear Technology 功能描述:DC-DC CONV, BUCK/BOOST, 8000mA, DFN-8 制造商:Linear Technology 功能描述:DC-DC CONV, BUCK/BOOST, 8000mA, DFN-8, Primary Input Voltage:5.5V, No. of Outputs:1, Output Current:800mA, No. of Pins:8, Operating Temperature Min:-40C, Operating Temperature Max:85C, MSL:MSL 1 - Unlimited, Package / Case:8-DFN , RoHS Compliant: Yes 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, Cut Tape 800mA, 1MHz Wide Input Voltage Synch Buck-Boost DC
LTC3538EDCB#TRMPBF 功能描述:IC REG BUCK BOOST SYNC ADJ 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓(降壓) 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON(1.45x1) 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2
LTC3538EDCB#TRPBF 功能描述:IC REG BUCK BOOST SYNC ADJ 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓(降壓) 輸出類型:固定 輸出數:1 輸出電壓:1.2V,1.5V,1.8V,2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP,10-MSOP(0.118",3.00mm 寬)裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤