- 您現(xiàn)在的位置：買賣IC網 > PDF目錄385507 > LTC3464 (Linear Technology Corporation) 1.2MHz Step-Up DC/DC Converter in SOT-23 PDF資料下載
參數資料
| 型號： | LTC3464 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 1.2MHz Step-Up DC/DC Converter in SOT-23 |
| 中文描述： | 1.2MHz升壓型DC / DC轉換器采用SOT - 23 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 152K |
| 代理商： | LTC3464 |
5
LTC3426
3426f
OPERATIOU
The LTC3426 is a monolithic 1.2MHz boost converter
housed in a 6-lead SOT-23 package. The device features
fixed frequency, current mode PWM control for excellent
line and load regulation. The low R
DS(ON)
NMOS switch
enables the device to maintain high efficiency over a wide
range of load current. Operation of the feedback loop
which sets the peak inductor current to keep the output in
regulation can be best understood by referring to the Block
Diagram in Figure 1. At the start of each clock cycle a latch
in the PWM logic is set and the NMOS switch is turned on.
The sum of a voltage proportional to the switch current
and a slope compensating voltage ramp is fed to the
positive input to the PWM comparator. When this voltage
exceeds either a voltage proportional to the 2A current
limit or the PWM control voltage, the latch in the PWM
logic is reset and NMOS switch is turned off. The PWM
control voltage at the output of the error amplifier is the
amplified and compensated difference between the feed-
back voltage on the FB pin and the internal reference
voltage of 1.22V. If the control voltage increases, more
current is delivered to the output. When the control voltage
exceeds the I
LIMIT
reference voltage, the peak current is
limited to a minimum of 2A. The current limit helps protect
the LTC3426 internal switch and external components
connected to it. If the control voltage decreases, less
current is delivered to the output. During load transients
control voltage may decrease to the point where no
switching occurs until the feedback voltage drops below
the reference. The LTC3426 has an integrated soft-start
feature which slowly ramps up the feedback control node
from 0V. The soft-start is initiated when SHDN is pulled
high.
APPLICATIU
Setting the Output Voltage
The output voltage, V
OUT
, is set by a resistive divider from
V
OUT
to ground. The divider tap is tied to the FB pin. V
OUT
is set by the formula:
W
U
U
V
R
R
OUT
=
+
1 22
.
1
1
2
Inductor Selection
The LTC3426 can utilize small surface mount inductors
due to its 1.2MHz switching frequency. A 1.5
μ
H or 2.2
μ
H
inductor will be the best choice for most LTC3426 appli-
cations. Larger values of inductance will allow greater
output current capability by reducing the inductor ripple
current. Increasing the inductance above 3.3
μ
H will in-
crease component size while providing little improve-
ment in output current capability. The inductor current
ripple is typically set for 20% to 40% of the maximum
inductor current (I
P
). High frequency ferrite core inductor
materials reduce frequency dependent power losses com-
pared to cheaper powdered iron types, improving effi-
ciency. The inductor should have low DCR (DC resistance)
to reduce the I
2
R power losses, and must be able to
handle the peak inductor current without saturating.
Several inductor manufacturers are listed in Table 1.
Table 1. Inductor Manufacturers
TDK
Sumida
Murata
www.tdk.com
www.sumida.com
www.murata.com
Output and Input Capacitor Selection
Low ESR (equivalent series resistance) capacitors should
be used to minimize the output voltage ripple. Multilayer
ceramic capacitors are an excellent choice as they have
extremely low ESR and are available in small footprints. A
15
μ
F to 30
μ
F output capacitor is sufficient for most
applications. X5R and X7R dielectric materials are pre-
ferred for their ability to maintain capacitance over wide
voltage and temperature ranges.
Low ESR input capacitors reduce input switching noise
and reduce the peak current drawn from the input supply.
It follows that ceramic capacitors are also a good choice
for input decoupling and should be located as close as
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3445 | 12-Bit To 24-Bit Multiplexed D-Type Latch With 3-State Outputs 56-SSOP -40 to 85 |
| LTC3445EUF | I2C Controllable Buck Regulator with Two LDOs in a 4mm ?4mm QFN |
| LTC3700 | Constant Frequency Step-Down DC/DC Controller with LDO Regulator |
| LTC3700EMS | Constant Frequency Step-Down DC/DC Controller with LDO Regulator |
| LTC4064 | Monolithic Linear Charger for Back-Up Li-Ion Batteries |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3490 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Single Cell 350mA LED Driver |
| LTC3490EDD | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Single Cell 350mA LED Driver |
| LTC3490EDD#PBF | 功能描述:IC LED DRIVER PHOTO FLASH 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:60 系列:- 恒定電流:- 恒定電壓:- 拓撲:線性（LDO），PWM，升壓（升壓） 輸出數:8 內部驅動器:是 類型 - 主要:背光 類型 - 次要:RGB，白色 LED 頻率:500kHz ~ 1.5MHz 電源電壓:4.75 V ~ 26 V 輸出電壓:45V 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* 工作溫度:-40°C ~ 85°C |
| LTC3490EDD#TRPBF | 功能描述:IC LED DRIVER PHOTO FLASH 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:6,000 系列:- 恒定電流:- 恒定電壓:- 拓撲:開路漏極，PWM 輸出數:4 內部驅動器:是 類型 - 主要:LED 閃爍器 類型 - 次要:- 頻率:400kHz 電源電壓:2.3 V ~ 5.5 V 輸出電壓:- 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-HVSON 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C 其它名稱:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3490ES8 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Single Cell 350mA LED Driver |
發(fā)布緊急采購，3分鐘左右您將得到回復。